Танилцуулга
The Behringer CLOCKED SEQUENTIAL CONTROL MODULE 1027 is a faithful reproduction of the legendary 2500 Series 8-position step sequencer. Designed for Eurorack systems, this module provides precise control over voltage and gate signals, making it an essential tool for creating complex melodic and rhythmic patterns in your modular synthesizer setup. Its robust design and intuitive interface ensure reliable performance and creative flexibility.
Аюулгүй байдлын чухал заавар
- Read these instructions thoroughly before operating the module.
- Эдгээр зааврыг цаашид лавлах зорилгоор хадгална уу.
- Бүтээгдэхүүн болон гарын авлага дээрх бүх анхааруулгыг анхаарч үзээрэй.
- Аюулгүй ажиллагааг хангахын тулд бүх зааврыг дагана уу.
- Энэ төхөөрөмжийг ус эсвэл чийгийн ойролцоо бүү ашигла.
- Зөвхөн хуурай даавуугаар цэвэрлэ.
- Агааржуулалтын нүхийг хааж болохгүй. Үйлдвэрлэгчийн зааврын дагуу суурилуулна.
- Радиатор, халаалтын төхөөрөмж, зуух болон бусад төхөөрөмж (үүнд ampөргөгч) дулаан үүсгэдэг.
- Зөвхөн үйлдвэрлэгчээс заасан хавсралт/дагалдах хэрэгслийг ашиглана уу.
- Бүх засвар үйлчилгээг мэргэшсэн үйлчилгээний ажилтнуудад хандаарай. Төхөөрөмж ямар нэгэн байдлаар гэмтсэн тохиолдолд засвар үйлчилгээ хийх шаардлагатай.
Тохиргоо
Eurorack суурилуулалт
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 is designed for installation into a standard Eurorack case. Ensure your Eurorack case has sufficient power and space (16 HP width) before installation.
- Унтраах: Always disconnect power from your Eurorack case before installing or removing any modules.
- Суурилуулалт: Align the module with an available 16 HP space in your Eurorack case. Secure it using the provided screws.
- Эрчим хүчний холболт: Connect the 16-pin power cable from your Eurorack power supply to the module's power header. Ensure the red stripe on the cable aligns with the -12V pin on both the module and the power supply. Incorrect connection can damage the module and/or power supply.
- Асаах: Аюулгүй суурилуулж, холбосны дараа та Eurorack гэрээ асааж болно.
Зураг 1: Урд view of the Behringer 1027 module, showing all controls and patch points. This image illustrates the module's layout for proper installation and connection within a Eurorack system.
Анхны холболтууд
To begin using the 1027, connect its outputs to other modules in your Eurorack system. Common connections include:
- Clock Input (CLK IN): Connect a clock signal from another module (e.g., an LFO or clock divider) to the CLK IN jack to drive the sequencer.
- CV Outputs (CH A, CH B, CH C): Patch these outputs to the CV inputs of oscillators, filters, or other modules to control pitch, cutoff, or other parameters.
- Gate Outputs (POSITION GATES 1-8): Connect these to gate inputs of envelope generators or drum modules to trigger events at specific steps.
Зураг 2: Ойрын зураг view of the input and output jacks on the Behringer 1027 module, highlighting the various patch points for integration into a modular system.
Ашиглалтын заавар
Дууслааview Хяналтын
The 1027 module features a clear layout of controls for intuitive sequencing:
- RATE бариул: Adjusts the speed of the internal clock. The range switch (LOW/HIGH) selects the clock speed range.
- PULSE WIDTH Knob: Controls the width of the gate pulses. The switch (INT/EXT) selects between internal control or external CV control.
- ON/OFF унтраалга: Toggles the sequencer's operation.
- АЛХАМ Товчнууд (1-8): Each step has a corresponding button to activate/deactivate it.
- CV Knobs (A, B, C for each step): Adjust the control voltage output for each of the three channels (A, B, C) at each step.
- POSITION GATES (1-8): Individual gate outputs for each step.
- STEP/RESET Buttons: Manual step advance and reset functions.
Зураг 3: Өнцөг view of the Behringer 1027 module, providing a clear perspective of the control knobs and buttons for each step and channel.
Creating a Sequence
- Цаг тохируулах: -г ашиглана уу ҮНЭ бариул ба БАГА/ӨНДӨР switch to set the desired tempo. Alternatively, connect an external clock to the CLK IN Жак.
- Activate Steps: дээр дарна уу АЛХАМ buttons (1-8) to activate the desired number of steps in your sequence. Active steps will typically illuminate.
- Adjust CV: For each active step, turn the CV Knobs (A, B, C) боть тохируулахtage level for each channel. These voltages will be outputted sequentially.
- Configure Gates: The Байрлалын хаалга will output a pulse when their corresponding step is active. Use these to trigger envelopes or other events.
- Эхлэх/ зогсоох: -г ашиглана уу ON/OFF switch to start and stop the sequence.
Нарийвчилсан шинж чанарууд
- External Pulse Width Control: Connect a CV source to the EXT input for the PULSE WIDTH section to dynamically control the gate pulse width.
- Manual Step/Reset: The АЛХАМ болон RESET buttons allow for manual control over the sequence progression, useful for live performance or precise programming.
Засвар үйлчилгээ
Цэвэрлэгээ
To maintain the appearance and functionality of your module:
- Always power off your Eurorack system before cleaning.
- Use a soft, dry, lint-free cloth to wipe the module's surface.
- Зөрүүд шороонд бага зэрэг dampдаавуугаар усаар. Хүчтэй химийн бодис, зүлгүүрийн цэвэрлэгч хэрэглэхээс зайлсхий.
- Do not allow any liquids to enter the module through jacks or openings.
Хадгалах
When not in use for extended periods, store the module in a cool, dry place, away from direct sunlight and extreme temperatures. If removed from the Eurorack case, store it in anti-static packaging.
Алдааг олж засварлах
| Асуудал | Боломжит шалтгаан | Шийдэл |
|---|---|---|
| Модуль асахгүй байна. | Incorrect power cable connection; Eurorack power supply off or faulty. | Check power cable orientation (red stripe to -12V). Ensure Eurorack power supply is on and functioning correctly. |
| Sequencer not advancing steps. | No clock signal; ON/OFF switch is OFF; RATE knob set too low. | Connect a clock signal to CLK IN. Ensure ON/OFF switch is ON. Increase the RATE knob setting. |
| No CV output from a channel. | CV knob for that step/channel is at minimum; step is not active. | Adjust the corresponding CV knob. Ensure the step is active (illuminated). |
| No Gate output from a position. | Step is not active; PULSE WIDTH set to minimum. | Ensure the step is active. Increase the PULSE WIDTH setting. |
Үзүүлэлтүүд
| Онцлог | Дэлгэрэнгүй |
|---|---|
| Загварын нэр | 1027 |
| Модулийн төрөл | Цагийн дараалсан хяналтын модуль |
| Цуврал | 2500 цуврал |
| Формат | Еврорак |
| Өргөн | 16 HP |
| Гүн | Not specified (typical Eurorack depth) |
| Эрчим хүчний хэрэглээ | Not specified (standard Eurorack +12V, -12V) |
| Оролтууд | Clock In, External Pulse Width CV |
| Гаралт | 3 x CV (A, B, C), 8 x Gate (Position Gates) |
| Хэмжээ (H x W x D) | 43 x 162 x 129 мм (ойролцоогоор 1.69 x 6.38 x 5.08 инч) |
| Зүйлийн жин | 0.77 фунт (ойролцоогоор 0.35 кг) |
| Холболтын технологи | 3.5mm TS jack |
| Эрчим хүчний эх үүсвэр | DC power supply (via Eurorack bus) |
Баталгаат хугацаа
Behringer products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please visit the official Behringer website or the Music Tribe Community portal. Warranty services are typically handled through authorized service centers.
Баталгаат тодорхойлолт: Community. Musictribe. Com.
Дэмжлэг
For further assistance, technical support, or to download the latest firmware and documentation, please visit the official Behringer webсайт:
- Берингерийн албан ёсны Webсайт
- Music Tribe Community (for warranty and support information)
You can also contact your local Behringer dealer or distributor for product-specific inquiries.