Rakstore ZB2L3 Battery Capacity Tester User Manual

1. Танилцуулга

The Rakstore ZB2L3 Battery Capacity Tester is a versatile device designed to measure the capacity of various battery types, including 18650 Lithium batteries and Lead-Acid batteries. It functions as a discharge tester, allowing users to determine the actual capacity by discharging the battery through a load and measuring the discharged energy. This manual provides detailed instructions for the safe and effective use of the ZB2L3 tester.

2. Аюулгүй байдлын мэдээлэл

• Always ensure correct polarity when connecting batteries to avoid damage to the tester and battery.
• Use appropriate discharge loads. Overloading the tester or using incorrect loads can cause overheating and damage.
• Зайны терминалуудад богино холболт үүсгэж болохгүй.
• Operate the device in a well-ventilated area, especially when discharging batteries, as they can generate heat.
• Төхөөрөмжийг чийг, хэт өндөр температураас хол байлга.
• Энэ төхөөрөмж нь тоглоом биш юм. Хүүхэд хүрэхгүй газар хадгалах.

3. Бүтээгдэхүүний онцлог

• Эрчим хүчний хангамж: DC4.5-6V via micro USB interface.
• Ажиллаж буй гүйдэл: Less than 70mA.
• Ус зайлуулах ботьtage хүрээ: 1-15V with 0.01V resolution.
• Дуусгах ботьtage хүрээ: 0.5-11.0 В.
• Supported Discharge Current: Up to 3.000A with 0.001A resolution.
• Ботьtage Хэмжилтийн алдаа: Less than 1% + 0.02V.
• Одоогийн хэмжилтийн алдаа: Less than 1.2% ± 0.002A.
• Зайны багтаамжийн хүрээ: Up to 9999Ah (1Ah=1000mAh). Display adjusts decimal point for large values (e.g., X.XXX Ah, XX.XX Ah).
• Компакт хэмжээ: Circuit board 50mm x 37mm, finished product 50mm x 37mm x 17mm (L x W x H, including copper foot height).

4. Багцын агуулга

• 1 x Rakstore ZB2L3 Battery Capacity Tester Unit
• (Note: Discharge resistors and battery holders are typically sold separately and are required for operation.)

5. Тохиргоо

Before operating the ZB2L3 tester, ensure all connections are made correctly.

Figure 1: ZB2L3 Battery Capacity Tester showing the micro USB power input, battery terminals, and load terminals.

1. Цахилгаан хангамжийн холболт: Connect a DC 4.5-6V power source to the micro USB port on the tester. A standard phone charger or power bank can be used. The display should light up.
2. Зайны холболт: Connect the battery to be tested to the "BAT+" and "BAT-" terminals. Ensure correct polarity. The tester will display the current battery voltage.
3. Discharge Load Connection: Connect an appropriate discharge resistor (load) to the "LOAD+" and "LOAD-" terminals. The resistance value of the load will determine the discharge current. Ensure the load can handle the expected power dissipation.

Чухал: The discharge current should not exceed 3.000A. Calculate the required resistance using Ohm's Law (R = V/I) and Power Law (P = V*I or P = I²*R) to ensure the resistor can handle the power. For example, if testing a 3.7V battery at 1A, you need a 3.7 Ohm resistor capable of dissipating at least 3.7W.

6. Ашиглалтын заавар

Follow these steps to perform a battery capacity test:

Figure 2: ZB2L3 Battery Capacity Tester showing the 'OK', '+', and '-' buttons for operation.

1. Анхны дэлгэц: After connecting the power and battery, the tester will display the battery's current voltage.
2. Set Termination Voltage:
   • Press the "OK" button once. The display will show the current termination voltage (e.g., "U 3.00").
   • Use the "+" and "-" buttons to adjust the termination voltage. This is the voltage at which the discharge test will stop. For 18650 Lithium batteries, a common termination voltage is 3.0V. For Lead-Acid batteries, consult the battery's specifications.
   • Press "OK" again to confirm the setting and return to the main display.
3. Start Discharge Test:
   • With the battery and load connected, and the termination voltage set, press and hold the "OK" button for approximately 3 seconds.
   • The tester will begin discharging the battery through the connected load. The display will cycle through current voltage (V), discharge current (A), and accumulated capacity (Ah).
4. Monitor Test Progress: Observe the display. The voltage will gradually decrease, and the accumulated capacity will increase.
5. Test Completion: The test will automatically stop when the battery voltage reaches the set termination voltage. The display will then show the final accumulated capacity (Ah) and flash.
6. View Үр дүн: After the test stops, you can press the "OK" button to cycle through the final voltage, current, and capacity readings.
7. Reset for New Test: To start a new test, disconnect the battery and load, then reconnect them, or simply press and hold the "OK" button again to clear the previous results and start a new cycle.

7. Засвар үйлчилгээ

• Цэвэрлэгээ: Төхөөрөмжийг цэвэрлэхийн тулд зөөлөн, хуурай даавуу ашиглана уу. Шингэн цэвэрлэгч, уусгагчийг бүү ашигла.
• Хадгалах: Шалгагчийг нарны шууд тусгал, хэт температураас хол, сэрүүн, хуурай газар хадгална.
• Шалгалт: Periodically check the terminals and connections for any signs of wear or damage.

8. Алдаа засах

9. Техникийн үзүүлэлтүүд

10. Баталгаат хугацаа ба дэмжлэг

This product is manufactured by Rakstore. For any technical support or warranty inquiries, please refer to the retailer where the product was purchased or visit the official Rakstore webхолбоо барих мэдээлэл авах сайт.

Баталгаат заргад зориулж худалдан авалтаа нотлох баримтаа үлдээнэ үү.