FTVOGUE Multifunction Time Delay Relay Module User Manual

1. Танилцуулга

This manual provides detailed instructions for the installation, operation, and maintenance of the FTVOGUE Multifunction Time Delay Relay Module. This module is designed for industrial automation control, offering 20 programmable functions per channel and a wide operating voltage range of DC 8V to 36V. Please read this manual thoroughly before use to ensure proper functionality and safety.

Figure 1.1: FTVOGUE Multifunction Time Delay Relay Module. This image shows the top view of the relay module, highlighting its compact design and various components including the digital display and control buttons.

2. Аюулгүй байдлын мэдээлэл

• Эрчим хүчний хангамжийн хэмжээг баталгаажуулна ууtage is within the specified range (DC 8V to 36V) to prevent damage to the module.
• Утас холбох эсвэл салгахаасаа өмнө үргэлж цахилгааныг салга.
• Wiring should be performed by qualified personnel to avoid electrical hazards.
• Модулийг чийг, хэт өндөр температур, идэмхий орчинд бүү тавь.
• The module features power anti-reverse connection protection, but always double-check polarity during installation.

3. Бүтээгдэхүүний онцлог

• Олон талт хяналт: Offers 4 channels with 20 programmable functions per channel for complex automation tasks.
• Өргөн ботьtage Range & Safety: Operates on 8-36V DC power with built-in power anti-reverse connection protection.
• Precise Timing Control: Programmable timing functions down to 1-second intervals with less than 1% error.
• Enhanced Visual Feedback: Clear power and relay status indicators via bright LED lights.
• Эрчим хүчний хэмнэлттэй дизайн: Automatic power-saving technology and memory retention for settings during power cycles.

Figure 3.1: Multifunction Relay Module. This image highlights the module's power indicator light and relay suction indicator lights, providing visual feedback on its operational status.

4. Багцын агуулга

• 1 x FTVOGUE Multifunction Time Delay Relay Module

5. Module Overview and Port Description

The module features various ports for power input, signal input, and relay load output. Understanding these connections is crucial for proper setup.

Figure 5.1: Module Port Layout. This image provides a clear top-down view of the relay module, detailing the VIN, GND, OFF, COM, IN1-IN4 terminals, and the relay load output connections.

Модуль ботьtage/Signal Input Terminal (8-line interfaces):

• VIN: DC positive pole for power input.
• GND: DC negative pole for power input.
• Унтрааж байна: Power control terminal.
• COM: Common end of photoelectric isolation signal input.
• IN1-IN4: Input signal detection interfaces.

Жич: The input signal detection interfaces (IN1-IN4) can be configured for either active-high or active-low operation. This selection is made via the COM port. If COM is connected to 'H' (High), IN1-IN4 will be active high. If COM is connected to 'L' (Low), IN1-IN4 will be active low.

Relay Load Output Terminal (12-wire interface):

These terminals are used to connect the devices or circuits that the relays will control. Each relay has normally open (NO), normally closed (NC), and common (COM) contacts.

Figure 5.2: Module Bottom View. This image displays the underside of the relay module, showing the solder points and circuit board traces, which can be useful for understanding the internal layout.

6. Тохиргоо

6.1 Эрчим хүчний холболт

1. Connect the positive terminal of your DC 8V-36V power supply to the VIN terminal on the module.
2. Connect the negative terminal of your DC power supply to the GND terminal on the module.
3. Ensure all power connections are secure and correct polarity is observed, despite the anti-reverse protection.

6.2 Signal Input Connection

1. Determine if your input signals are active-high or active-low.
2. For active-high signals, connect the COM terminal to a high logic level (e.g., VCC).
3. For active-low signals, connect the COM terminal to a low logic level (e.g., GND).
4. Connect your control signals to the respective IN1, IN2, IN3, ба IN4 терминалууд.

6.3 Relay Load Connection

1. Identify the common (COM), normally open (NO), and normally closed (NC) contacts for each relay.
2. Connect your load device according to your application requirements (e.g., connect one side of the load to the relay's COM and the other side to NO for normally open operation).
3. Одоогийн болон боть байгаа эсэхийг шалгаарайtage ratings of your loads do not exceed the relay's specifications (e.g., 10A 250VAC / 10A 30VDC).

7. Ашиглалтын заавар

The FTVOGUE Multifunction Time Delay Relay Module offers 20 distinct operating functions, configurable via the onboard buttons and displayed on the 4-digit LED segment display.

Figure 7.1: Relay Module with Dimensions. This image shows the physical dimensions of the module (8.5cm x 7.5cm), which is helpful for installation planning.

7.1 Function Selection and Parameter Setting

• The module typically features buttons labeled 'SET', '+', '-', and 'SAVE' (or similar) for navigation and parameter adjustment.
• Press the 'SET' button to enter the function selection mode. The LED display will show the current function number.
• Use the '+' and '-' buttons to cycle through the 20 available functions. Each function corresponds to a specific timing or control logic.
• Once a function is selected, press 'SET' again to enter parameter adjustment mode for that function.
• Use '+' and '-' to adjust timing values (e.g., delay time, pulse width) or other function-specific parameters. The timing can be set with 1-second precision.
• After setting all parameters, press the 'SAVE' button to store the configuration. The module will retain these settings even after power cycles.

7.2 LED үзүүлэлтүүд

• Эрчим хүчний LED: Illuminates when the module is powered on.
• Relay Status LEDs: Individual LEDs for each relay indicate its current state (e.g., ON when the relay is activated, OFF when deactivated). These provide immediate visual confirmation of relay operation.

8. Засвар үйлчилгээ

• Модулийг цэвэр, тоос шороо, хог хаягдлаас цэвэр байлга. Цэвэрлэхэд зөөлөн, хуурай даавуу ашиглаарай.
• Regularly inspect wiring connections for looseness or corrosion.
• Ашиглаагүй үедээ модулийг хуурай, сэрүүн орчинд хадгална уу.
• Avoid applying excessive force to the terminals or buttons.

9. Алдаа засах

• Модуль асахгүй байна: Цахилгаан хангамжийн эзлэхүүнийг шалгана ууtage and polarity (VIN/GND connections). Ensure the power control terminal (OFF) is correctly configured if used.
• Relay not activating: Verify input signal (IN1-IN4) is correct and COM port is set for active-high/low accordingly. Check the selected function and its parameters. Ensure the load is correctly wired to the relay contacts.
• Буруу цаг хугацаа: Re-enter parameter adjustment mode and verify the set timing values. Ensure the correct function is selected.
• Тохиргоо хадгалагдахгүй байна: Ensure the 'SAVE' button (or equivalent) is pressed after making changes.

10. Техникийн үзүүлэлтүүд

11. Баталгаат хугацаа ба дэмжлэг

For warranty information or technical support, please refer to the product packaging or contact your retailer/seller directly. Keep your purchase receipt as proof of purchase.