FeiyuTech SCORP 2 3-Axis Handheld Gimbal Stabilizer User Manual

1. гаруйview

The FeiyuTech SCORP 2 is a versatile 3-axis handheld gimbal stabilizer designed for mirrorless and DSLR cameras. It features a built-in AI tracking module, a 1.3-inch touchscreen, and an integrated handle for enhanced control and comfort. The quick-release design allows for instant vertical filming setup without additional accessories.

2. Эхлэл

2.1 Цэнэглэж байна

Before initial use, fully charge the gimbal battery. Use the provided USB-C cable for charging. The gimbal supports quick charging with power up to 18W.

2.2 Adjust the Gimbal to Balancing Position

The gimbal is folded by default. Unlock all three axes and adjust the gimbal to its balancing position, then lock the axes. This prepares the gimbal for camera mounting and balancing.

2.3 Using Support Stand

The gimbal can be placed on a flat surface using its built-in kickstand or by attaching the included tripod.

3. Камер суурилуулах

Before mounting your camera, ensure it is ready for shooting: lens installed, lens cover removed, memory card and battery inserted, and battery fully charged. The gimbal should be powered off or in sleep mode and adjusted to the balancing position.

3.1 Attach the Quick Release Plate and Camera Backing Base (Optional)

Attach the quick release plate to your camera by tightening the screw. For long or heavy lenses, attach the camera backing base to the camera, then secure it to the quick release plate with two screws.

3.2 Install Lens Holder (Optional)

If needed, install the lens holder on the quick release plate, ensuring the rubber part is directly under the lens. This is recommended for long or heavy lenses.

3.3 Mount Camera on Gimbal

Unlock the gimbal, slide the camera assembly into the slot, then lock it. Loosen the appropriate adjustment, slide the camera assembly as indicated, and adjust the camera forward and backward until it is roughly balanced. Finally, tighten the adjustment.

4. Гимбал тэнцвэржүүлэх

Proper balancing is crucial for optimal performance. Ensure the camera and lens are ready, and the gimbal is off or in sleep mode. It is recommended to hold the camera up while adjusting the slide arm, cross arm, and vertical arm.

4.1 Balancing the Tilt Axis

Unlock the tilt lock and loosen the slide arm lock. Rotate the tilt axis so the camera lens points upward. If the lens tilts to one side, move the slide arm in the opposite direction until the camera is steady. Tighten the slide arm lock while holding the camera. For depth adjustment, rotate the tilt axis so the lens points forward. If it tilts, unlock the quick release plate and move it in the opposite direction until steady. Lock the quick release plate. The tilt axis is balanced when the camera remains steady when tilted up or down by 45 degrees.

4.2 Balancing the Roll Axis

Unlock the roll lock. If the camera tilts to one side, loosen the cross arm lock knob and move the cross arm in the opposite direction until the camera is horizontal and steady. Tighten the cross arm lock knob. The roll axis is balanced when the camera stays still and horizontal.

4.3 Balancing the Pan Axis

Unlock the pan lock. Hold the tripod and tilt the gimbal forward until it is horizontal. If the camera tilts, loosen the vertical arm lock knob and move the vertical arm in the opposite direction until the camera is horizontal and steady. Tighten the vertical arm lock knob. The pan axis is balanced when the camera stays still and horizontal.

4.4 Using the Memory Slider

The Feiyu SCORP 2 includes a memory slider to simplify re-balancing. After balancing, move the memory slider to a hole in the axis so the red dot is exposed. This marks the current position. For future setups with the same equipment, simply align the red dot to quickly achieve balance.

5. Power ON/OFF & Wake Up

5.1 Асаах/унтраах

Before powering on, ensure the gimbal is balanced and all three axes are unlocked. If axes are locked, the gimbal will enter sleep mode for protection. Long press the power button until you hear a beep to power on/off. For first-time use or after changing cameras/lenses, set motor power (refer to section 8.3.1).

5.2 Lock/Unlock Screen

Single tap the F2 button to lock the screen. Single tap F2 again to unlock.

5.3 Sleep/Wake Up

Double tap the power button to enter sleep mode. To wake up, single tap the power button or tap the 'Z' icon on the screen.

6. Функц/Гохимуудын танилцуулга

6.1 Follow Modes

• PF (Pan Follow): Only the pan axis follows your hand movement.
• PTF (Pan and Tilt Follow): Both pan and tilt axes follow your hand movement; roll axis does not.
• FPV (Анхны хүн View): All three axes (pan, tilt, roll) follow your hand movement.
• Түгжих: All three axes are fixed, maintaining the camera's direction.
• FFW (Flash Follow): All three axes follow your hand movement at high speed.

6.2 Бусад функцууд

• Автомат эргүүлэх: Achieve image rotating scenes by setting rotation speed and direction.
• Хөрөг горим: Enter portrait mode for vertical video recording or live streaming.
• Selfie горим: Camera turns 180° horizontally for selfie shooting.
• Track Video: Record video along preset waypoints.
• Гараар түгжих: Manually move the camera to a desired position and hold for half a second to save new tilt/pan positions.

7. Програмыг холбох

7.1 Feiyu SCORP програмтай холбогдоно уу

To connect, turn on the gimbal and enable Bluetooth on your smartphone. Open the Feiyu SCORP App and tap the top of the home page to connect. Once connected, you can control the gimbal via the app, including virtual joystick control, mode switching, motor power/camera parameter adjustments, follow speed settings, and firmware updates.

7.2 Function Introduction of App

The Feiyu SCORP App provides extensive control and customization:

• Gimbal Control Access: Displays product name and battery level. Tap to access virtual joystick, switch follow modes, recenter gimbal, and adjust horizontal angle.
• Төхөөрөмжийг салгах: Tap to disconnect the current device.
• Хувилбарууд: Access auto rotation, panorama, timelapse (Motionlapse/Static timelapse/Hyperlapse), and track video.
• Товчлуурын тохиргоо: Customize trigger button functions, set auto focus time, and attitude change time for A/B buttons.
• Бариулын тохиргоо: Set the multifunction knob's control object (axes, electronic focus, focus motor), and adjust damp, speed, smooth, and sound.
• Motor Power Settings: Manually adjust motor power for tilt, roll, and pan axes, or use auto tune.
• Хурд дагах: Select preset profiles (Slow/Med/Fast) or customize follow speed and dead zone.
• Камерын тохиргоо: Adjust camera aperture, shutter speed, and ISO parameters when connected.
• Horizon Calibration: Calibrate the gimbal automatically or manually.
• Илүү: Set boot silent, disable selfie, manual lock, check firmware info, update firmware, and restore default settings.
• Буцах: Нүүр хуудас руу буцах.
• Connect with Image Transmission Device: Connect to an image transmission device.
• Joystick Settings: Adjust joystick speed for pan/tilt axis control and invert joystick direction.
• Сэргээх: Гимбалыг дахин тохируулахын тулд товшино уу.
• Flash Follow (FFW): Tap to enter Flash Follow mode.
• Хөрөг горим: Хөрөг горимд орохын тулд товшино уу.
• Selfie горим: Селфи горимд орохын тулд товшино уу.
• Adjust Horizontal Angle: Slide to control roll axis and adjust horizontal angle.
• Virtual Joystick: Use the virtual joystick to control pan and tilt axes.
• Түгжих горим: Түгжих горимд орохын тулд товшино уу.
• Хөшиг: Take photos or start/stop video recording.
• Switch between Photo/Video Mode: Фото болон видео горимуудын хооронд шилжих.
• Pan Follow (PF): Tap to enter Pan Follow mode.
• Pan and Tilt Follow (PTF): Tap to enter Pan and Tilt Follow mode.
• FPV: FPV горимд орохын тулд товшино уу.
• Хөдөлгөөн мэдрэгч горим: Control pan and tilt axes by moving your smartphone.

8. Үйл ажиллагаа

8.1 Товчлуурын ажиллагаа

• Цахилгаан товч: Long press for ON/OFF. Single tap for wake up (sleep mode) or battery level. Double tap to enter sleep mode.
• Горимын товчлуур: Single tap to cycle through PF/PTF/FPV. Tap five times for Horizon calibration.
• Триггер товчлуур: Double tap to recenter. Triple tap to enter/exit selfie mode. Press and hold for PTF (release to exit). Customizable via app.
• Жойстик: Controls tilt and pan axes movement.
• Хөшигний товчлуур: Half press for focus. Single tap (fully) to start/stop recording. Long press (fully) to take photo.
• FPV Button: Single tap to enter/exit FPV mode.
• F1 товчлуур: Double tap to enter/exit portrait mode. Triple tap for AI power ON/OFF. Long press to enter/exit AI Tracking (when AI power is enabled).
• F2 Button (Home Button): Single tap to lock/unlock screen (home page) or return to home page (other pages). Double tap to enter FFW mode. Long press for motor power auto tuning.
• A/B товчлуур: Long press to mark current position as A/B. Single tap to return to marked A/B position.
• Knob Function Switching Button: Single tap to switch control object (3 axes movement, electronic focus/zoom). Long press to cycle through multifunction knob control options.
• Олон үйлдэлт бариул: Turn to control roll, tilt, pan axes; focus/zoom; focus motor; or adjust parameters on the touchscreen.
• Түлхүүр хослолууд: Long press F1 + F2 buttons to clear Bluetooth connections.

8.2 Мэдрэгчтэй дэлгэцийн ажиллагаа

The 1.3-inch touchscreen provides intuitive control and information:

• Current Battery Level: Displays gimbal battery status.
• Камерын холболт: Icon appears when camera is successfully connected.
• Bluetooth холболт: Icon appears when Bluetooth is connected.
• Моторын хүч: Use auto tune or manually adjust motor power for each axis.
• Хурд дагах: Select preset or custom follow speed profiles.
• Дагах горим: Select desired gimbal follow mode.
• Хувилбар: Choose shooting scenarios like timelapse, auto rotation, panorama, portrait mode, selfie mode, track video.
• Joystick Settings: Adjust joystick speed and direction.
• Gimbal тохиргоо: Disable selfie, manual lock, horizon calibration.
• Bluetooth тохиргоо: Connect to camera or smartphone via Bluetooth.
• Арын гэрэлтүүлгийн тохиргоо: Дэлгэцийн тод байдлыг тохируулна уу.
• AI мөрдөх: Triple tap F1 or toggle via More Settings to turn AI power ON/OFF. Use gestures (spread palm for shutter, OK gesture for start/stop tracking, thumbs opposite direction for stop tracking, double L-shaped for custom framing).

8.3 Control Ports

The gimbal features a camera control port, an image transmission port, and two extension ports on the fixed plate for connecting accessories like a focus motor.

9. Хэрэглэгчийн зөвлөмж

• Камерын нийцтэй байдал: Always check the official FeiyuTech website for the latest camera and lens compatibility list to ensure optimal performance.
• Моторын чадлын тохируулга: If the gimbal vibrates at high frequency, the motor power might be too strong. If it shakes with low frequency and large amplitude, the motor power might be too weak. Adjust accordingly in the settings.
• Bluetooth холболт: Ensure your camera's Bluetooth function is enabled when attempting to connect the gimbal via Bluetooth for camera control.

10. Техникийн үзүүлэлтүүд

11. Дагалдах хэрэгсэл

The FeiyuTech SCORP 2 package includes the following items:

• USB 2.0 to USB-C Charging Cable x1
• USB-C-аас микро камерын хяналтын кабель x1
• USB-C-аас USB-C камерын хяналтын кабель x1
• USB-C-аас TRS2.5 камерын хяналтын кабель x1
• USB-C-ээс олон камерын хяналтын кабель x1
• USB-C-аас 2.5 мм-ийн камерын хяналтын кабель (DC2.5 мм) x1
• USB-C-аас TRS3.5 камерын хяналтын кабель x1
• USB-C-аас мини камерын хяналтын кабель x1
• Tripod x1
• Тогтмол хавтан x1
• Гулсагч x1
• Түргэн гаргах хавтан x1
• Camera backing base x1
• Линз эзэмшигч x1
• Линз эзэмшигчийн шураг x1
• Камерын бэхэлгээний шураг x3

12. Хадгалалт, засвар үйлчилгээ

• Бүтээгдэхүүнийг хүүхэд, тэжээвэр амьтдын гар хүрэхгүй газар хадгална уу.
• Do not leave the product near heat sources (furnace, heater) or inside a vehicle on hot days.
• Бүтээгдэхүүнийг хуурай орчинд хадгална.
• Do not overcharge or overuse the battery; charge it at least once a month if not used for a long time.
• Хэт өндөр эсвэл хэт бага температуртай үед бүтээгдэхүүнийг хэзээ ч бүү ашиглаарай.

13. Аюулгүй байдлын анхааруулга

Хэрэглээний ерөнхий анхааруулга

• Ensure motor spinning is not blocked by external force when powered on.
• Do not contact water or other liquids unless the product is marked waterproof/splash-proof. Avoid sea water or corrosive liquids.
• Do not disassemble the product except for marked detachable parts. If accidental disassembly occurs, contact FeiyuTech after-sales or an authorized service center for repair.
• Prolonged operation may cause the product surface temperature to rise; operate carefully.
• Do not drop or strike the product. Contact after-sales support if the product is abnormal.

IC цацрагийн өртөлтийн мэдэгдэл

Энэхүү төхөөрөмж нь хяналтгүй орчинд тогтоосон IC цацрагийн өртөлтийн хязгаарт нийцдэг.

FCC зохицуулалтын нийцэл

Энэ төхөөрөмж нь FCC дүрмийн 15-р хэсэгт нийцдэг. Ашиглалт нь дараах хоёр нөхцлийн дагуу явагдана: (1) Энэ төхөөрөмж нь хортой хөндлөнгийн оролцоо үүсгэхгүй, (2) энэ төхөөрөмж нь хүсээгүй ажиллагааг үүсгэж болзошгүй хөндлөнгийн оролцоо зэрэг хүлээн авсан аливаа хөндлөнгийн оролцоог хүлээн авах ёстой.

Жич: This equipment has been tested and found to comply with the limits for a Class B digital device. If interference occurs, try reorienting the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a radio/TV technician. Unauthorized modifications could void the user's authority to operate the equipment.

14. Баталгаат хугацаа ба дэмжлэг

For detailed support, please contact FeiyuTech:

• Үйлдвэрлэгч: Guilin Feiyu Technology Incorporated компани
• Webсайт: www.feiyu-tech.com
• И-мэйл: support@feiyu-tech.com
• Утас: +86 773-2320865

For a detailed user manual (PDF), please refer to the official document available at https://manuals.plus/m/e1a03aea816a350a697ab8d6ecd85eb15a6c3e2c27164c8620e81c23f51af6e9.