D149H181 Ed.08
AKO-D14918
The AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality
Анхааруулга
-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.
Тодорхойлолт
- LED COM
- БИЧЛЭГИЙН ТҮЛХҮҮР
- EXTERNAL POWER CONNECTOR
- READ KEY
- LED асаалттай байна
- CONNECTOR CABLE
Тохиромжтой байдал
Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.
Connecting incompatible devices can permanently damage the key.
Утас
- ЧУХАЛ: Pay attention to the orientation of the connector.
- АКО-80018
(Заавал биш) - AKO-D14918
Цахилгаан хангамж
-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (АКО-80018 or equivalent).
Үйл ажиллагаа
ЧУХАЛ: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.
RECORD key
Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.
READ key
It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.
LED асаалттай байна
Steady or flashing: Indicates that the key is connected to the controller.
LED COM
Тогтвортой: Indicates an error in the transmission/reception of data
Хурдан анивчих: Indicates transmission/reception of data in progress. At the end of the transmission LED COM унтрах болно.
Удаан анивчдаг: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.
ЖИЧ: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.
ЧУХАЛ: Хэзээ ч үгүй disconnect the programming key during data transmission.
Техникийн үзүүлэлтүүд
Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Нийлүүлэлт ботьtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Байгаль орчны үзүүлэлтүүд:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC
AKO ELECTROMECÁNICA, SA
Av. Roquetes, 30-38 | 08812 Сант Пере де Рибес | Барселона | Испани
35D149181 REV.07 2025
Манай Техникийн хуудсанд заасан материалаас бага зэрэг ялгаатай байж болзошгүй материалыг нийлүүлэх эрхтэй.
Шинэчлэгдсэн мэдээллийг манай сайтаас авах боломжтой webсайт.
Баримт бичиг / нөөц
 |
AKO D14918 Programming Key [pdf] Зааварчилгааны гарын авлага AKO-D14918, AKO-80018, D14918 Programming Key, Programming Key, Key |