Yamaha YT150 Guitar/Bass Auto Tuner Instruction Manual

Танилцуулга

The Yamaha YT150 is an auto tuner designed for both acoustic and electric guitars, as well as 4, 5, or 6-string bass guitars. It features a high-resolution LCD meter display for accurate tuning and LEDs for visibility in various lighting conditions. This manual provides instructions for the proper setup, operation, and maintenance of your YT150 tuner.

Зураг 1: Yamaha YT150 Guitar/Bass Auto Tuner. This image shows the front view of the Yamaha YT150 tuner, displaying its LCD screen and control buttons.

Тохиргоо

1. Зай суурилуулах

The YT150 tuner requires one CR2 battery (included). To install or replace the battery:

1. Төхөөрөмжийн арын хэсэгт зайны тасалгааг ол.
2. Зайны тасалгааны тагийг нээ.
3. CR2 батерейг зөв туйлшралтай (+/-) байлгаж оруулна уу.
4. Зайны тасалгааны тагийг сайтар хаа.

2. Хөгжмөө холбох

The YT150 offers two methods for connecting your instrument:

• For Electric Guitars/Basses: Connect your instrument to the tuner's ОРОЛТ jack using a standard 1/4-inch instrument cable. If you wish to pass the signal through to an amplifier, connect the tuner's ГАРЦ Жак руугаа ampөргөгчийн оролт.
• For Acoustic Guitars: Utilize the built-in microphone. Ensure the tuner is placed near the soundhole of your acoustic instrument for optimal sound detection.

Ашиглалтын заавар

1. Асаах/унтраах

Locate the power switch, typically a slide switch, on the side or back of the unit. Slide it to the "ON" position to power on the tuner. Slide it to the "OFF" position when not in use to conserve battery life.

2. Selecting Tuning Mode

The YT150 features an auto mode and a dedicated bass mode:

• Авто горим: This mode automatically detects the closest tone programmed in the tuner, providing fast and efficient tuning for both guitars and basses.
• Басс горим: For bass guitars, select the "bass mode" to display bass string notes in their proper order, optimizing the tuning experience for bass instruments.

3. Хэрэгслээ тааруулах

1. Хөгжим дээрээ ганц чавхдаст утас залгаарай.
2. Observe the LCD display. The display will show the detected note.
3. Adjust your instrument's tuning peg until the display indicates the correct note and the "in-tune" LED illuminates. The sharp/flat LEDs will guide you if the note is too high or too low.
4. Бүх мөрүүдийг давтана уу.

The large, easy-to-read liquid crystal display presents notes clearly, making tuning straightforward even from a distance or in low light conditions.

Засвар үйлчилгээ

1. Цэвэрлэгээ

Wipe the tuner with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the finish and internal components.

2. Хадгалах

When not in use for extended periods, remove the battery to prevent leakage and store the tuner in a cool, dry place away from direct sunlight and extreme temperatures.

3. Зай солих

If the display becomes dim or the tuner behaves erratically, it may be time to replace the battery. Refer to the "Battery Installation" section under Setup for instructions.

Алдааг олж засварлах

• Тохируулагч асахгүй байна:
  • Цахилгаан унтраалга "ON" байрлалд байгаа эсэхийг шалгаарай.
  • Check the battery. Replace it if it is depleted or incorrectly installed.
• Буруу тохируулга:
  • Ensure the instrument is properly connected (via cable for electric, or microphone for acoustic).
  • For acoustic instruments, ensure the tuner's microphone is close to the sound source and there is minimal background noise.
  • Pluck strings firmly and clearly, one at a time.
  • Check if the correct mode (Auto or Bass) is selected for your instrument.
• Дэлгэц бүдэг эсвэл анивчих:
  • Батерей бага байж магадгүй. Зайг солих.

Үзүүлэлтүүд

Баталгаат болон дэмжлэг

For warranty information and customer support, please refer to the documentation included with your purchase or visit the official Yamaha webсайт. Аливаа баталгаат нэхэмжлэлийн хувьд худалдан авалтаа нотлох баримтаа хадгалаарай.

Онлайн дэмжлэг: www.yamaha.com