Гүйцэтгэлийн хэрэгсэл W1611

Performance Tool W1611 2.25 Ton Trolley Jack Instruction Manual

Загвар: W1611

Танилцуулга

This manual provides essential instructions for the safe operation, maintenance, and storage of your Performance Tool W1611 2.25 Ton (4,500 lbs) Capacity Trolley Jack. Before using the jack, it is crucial to read and understand all instructions and safety warnings to prevent injury or property damage. Keep this manual for future reference.

Performance Tool W1611 2.25 Ton Trolley Jack

Image: The Performance Tool W1611 2.25 Ton Trolley Jack, a yellow hydraulic jack with a long handle.

Аюулгүй байдлын чухал мэдээлэл

WARNING: Failure to heed these warnings may result in personal injury or property damage.

  • Бүх зааврыг уншина уу: Understand the operation and limitations of the jack, as well as the hazards involved.
  • Хатуу, тэгш гадаргуу дээр хэрэглэнэ: Always use the jack on a hard, level surface capable of supporting the load. Avoid soft ground or uneven surfaces.
  • Do Not Exceed Rated Capacity: The W1611 jack has a maximum capacity of 2.25 tons (4,500 lbs). Do not attempt to lift loads heavier than this rating.
  • Жак тавиурыг ашиглах: This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Never work under a vehicle supported only by a jack.
  • Ачааллыг төвлөрүүлэх: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
  • Тодорхой байлгах: Keep hands, feet, and other body parts clear of moving parts and the area under the load.
  • Хэрэглэх бүрийн өмнө шалгах: Хэрэглэх бүрийн өмнө домкрат нь ямар нэгэн гэмтэл, гоожилт, сул эд анги байгаа эсэхийг шалгана уу. Гэмтсэн бол бүү хэрэглэ.
  • Lower Slowly: Always lower the load slowly and in a controlled manner.
  • Санал 65 Анхааруулга: Энэ бүтээгдэхүүн нь Калифорни мужид мэдэгдэж байгаа хорт хавдар, ургийн гажиг эсвэл нөхөн үржихүйн бусад гэмтэл учруулдаг химийн бодис агуулсан байж болзошгүй. Харьцуулсны дараа гараа угаана.

Багцын агуулга

Савлахдаа бүх бүрэлдэхүүн хэсгүүд байгаа эсэхийг шалгана уу:

  • 1 Performance Tool W1611 2.25 Ton Trolley Jack
  • 1 Operating Handle
  • 1 Blow-molded plastic storage case

Үзүүлэлтүүд

ОнцлогТодорхойлолт
ЗагварW1611
Ачааллын хүчин чадал2.25 тонн (4,500 фунт)
Хамгийн бага өргөх өндөр5-1/4 инч
Хамгийн их өргөх өндөр15 инч
Бүтээгдэхүүний хэмжээ (L x W x H)23.2 x 10.3 x 6.8 инч
Зүйлийн жинApproximately 27 lbs (including case)
ЭмээлSteel lifting saddle with 360-degree swivel
ДугуйHeavy-duty steel front wheels, ball-bearing swivel rear wheels
Detail of Performance Tool W1611 jack saddle and wheels

Зураг: Ойролцоогоор view highlighting the steel lifting saddle and the heavy-duty wheels of the trolley jack.

Тохиргоо ба эхний бэлтгэл

1. Савыг задлах

Carefully remove the trolley jack and its components from the packaging. Inspect for any shipping damage. If any damage is found, do not use the jack and contact customer support.

2. Бариулын угсралт

Insert the operating handle into the handle socket on the jack. Ensure it is securely seated. Some models may require tightening a set screw.

3. Bleeding the Hydraulic System

Before first use, or if the jack has been stored for an extended period, it is recommended to bleed any air from the hydraulic system to ensure proper operation. This procedure helps distribute fluid evenly through internal components.

  1. Locate the release valve (typically a screw or knob near the handle socket).
  2. Turn the release valve counter-clockwise to open it fully.
  3. Pump the handle vigorously six (6) to ten (10) times. This action will cycle the hydraulic fluid and expel any trapped air.
  4. Turn the release valve clockwise to close it firmly. The jack is now ready for use.

Ашиглалтын заавар

1. Тээврийн хэрэгслийг өргөх

  1. Машинаа бэлтгэх: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in 'Park' (automatic) or 'Reverse' (manual). Block the wheels that will remain on the ground to prevent movement.
  2. Жакыг байрлуул: Locate the manufacturer-recommended lifting points on your vehicle's frame or chassis. Position the jack so the saddle is directly under the lifting point. Ensure the jack is stable and the load is centered on the saddle.
  3. Машинаа өргөх: Close the release valve by turning it clockwise until it is firm. Pump the operating handle up and down to raise the vehicle to the desired height.
  4. Жак Стендээр аюулгүй болго: Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.

2. Тээврийн хэрэгслийг буулгах

  1. Талбайг цэвэрлэх: Ensure all tools, personnel, and obstructions are clear from under and around the vehicle.
  2. Бага зэрэг өргөх: Хэрэв тээврийн хэрэгсэл домкрат дээр байгаа бол тээврийн хэрэгслийг домкратаас бага зэрэг өргөхийн тулд домкрат бариулыг хэд хэдэн удаа шахна уу.
  3. Жакын суурийг ав: Тээврийн хэрэгслийн доороос домкрат тулгуурыг болгоомжтой авч хая.
  4. Тээврийн хэрэгслийг доошлуул: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Once fully lowered, remove the jack.
Performance Tool W1611 trolley jack in use

Image: The Performance Tool W1611 trolley jack positioned for lifting, demonstrating its extended handle and low profile.

Засвар үйлчилгээ

Regular maintenance ensures the longevity and safe operation of your trolley jack.

  • Цэвэрлэгээ: Keep the jack clean and free of dirt, grease, and debris. Wipe down the exterior with a clean cloth after each use.
  • Тосолгоо: Periodically lubricate the pivot points, wheels, and especially the wheel castor bearings with light machine oil to ensure smooth operation and prevent rust.
  • Гидравлик шингэн: Check the hydraulic fluid level periodically. If the fluid level is low, consult a qualified service technician for proper refilling with hydraulic jack oil. Do not use brake fluid or other non-specified fluids.
  • Шалгалт: Regularly inspect the jack for any signs of wear, damage, or leaks. Pay close attention to welds, the hydraulic cylinder, and the handle. If any issues are found, discontinue use and have it repaired by a qualified professional.

Алдааг олж засварлах

Нийтлэг асуудлууд болон тэдгээрийн боломжит шийдлүүдийг доорх хүснэгтээс харна уу.

АсуудалБоломжит шалтгаанШийдэл
Jack will not lift or lifts slowlyГидравлик систем дэх агаар
Гидравлик шингэний түвшин бага
Суллах хавхлага бүрэн хаагдаагүй байна
Bleed the hydraulic system (refer to Setup section)
Consult a qualified technician to check/refill fluid
Ensure release valve is firmly closed clockwise
Jack lowers under loadСуллах хавхлага бүрэн хаагдаагүй байна
Internal hydraulic leak
Хэт ачаалал
Ensure release valve is firmly closed
Discontinue use and consult a qualified technician
Ensure load does not exceed 2.25 tons (4,500 lbs)
Jack is difficult to pumpГидравлик систем дэх агаар
Хөдөлгөөнт хэсгүүдийн тосолгооны дутагдал
Damaged pump mechanism
Гидравлик системээс цус гарга
Lubricate pivot points and wheels
Мэргэшсэн техникчээс зөвлөгөө аваарай

Хадгалах

Proper storage helps maintain the jack's condition and readiness for use.

  • Хадгалахын өмнө цэвэрлэх: Ensure the jack is clean and dry before storing.
  • Lower Ram Fully: Always lower the jack's ram completely before storage to relieve pressure on the hydraulic system.
  • Хадгалах хайрцаг ашиглах: Store the jack in its provided blow-molded plastic case to protect it from dust, moisture, and damage. This also prevents it from rolling around if stored in a vehicle.
  • Хуурай газар хадгалах: Store the jack in a dry, protected area, away from corrosive materials and extreme temperatures.
Performance Tool W1611 trolley jack and its storage case

Image: The Performance Tool W1611 trolley jack alongside its durable black plastic storage case, emphasizing portability and protection.

Баталгаат болон дэмжлэг

For warranty information or technical support regarding your Performance Tool W1611 2.25 Ton Trolley Jack, please refer to the documentation included with your purchase or visit the official Performance Tool webсайт. Харилцагчийн үйлчилгээний холбоо барих мэдээллийг ихэвчлэн үйлдвэрлэгчийн вэбсайтаас авах боломжтой. webсайт эсвэл бүтээгдэхүүний сав баглаа боодол.

хаягаар зочилж болно Performance Tool Store on Amazon бүтээгдэхүүний талаарх дэлгэрэнгүй мэдээлэл, дэмжлэгийн эх сурвалжийг авна уу.

Холбогдох баримт бичиг - W1611

Урьдчилсанview Гүйцэтгэлийн хэрэгсэл W1630 1-1/2 тонн бага Profile Хөнгөн цагаан шалны Жак эзэмшигчийн гарын авлага
Performance Tool W1630 1-1/2 Ton Low Pro-ийн эзэмшигчийн гарын авлагаfile Хөнгөн цагаан шалны үүр, аюулгүй байдал, ашиглалт, засвар үйлчилгээ, эд анги, алдааг олж засварлах талаар дэлгэрэнгүй.
Урьдчилсанview Performance Tool 3 Ton Jack Stands Owner's Manual
This owner's manual provides essential information for the Performance Tool 3 Ton Jack Stands (Item Number W1619), including detailed specifications, critical safety guidelines, operating instructions, care and maintenance procedures, and limited warranty details. Ensure safe and effective use of your jack stands by thoroughly reading and understanding this guide.
Урьдчилсанview Digital Automotive Multimeter Owner's Manual - Performance Tool W2972/W2969
Comprehensive owner's manual for the Performance Tool W2972/W2969 Digital Automotive Multimeter, covering safety information, specifications, basic tests, mechanical tests, battery/starting/charging, engine sensors, ignition systems, fuel systems, and maintenance.
Урьдчилсанview Digital Automotive Multimeter Owner's Manual
This owner's manual provides comprehensive instructions for using the Performance Tool Digital Automotive Multimeter (Model W2972/W2969) for various automotive diagnostic tests, including electrical, engine, fuel, and ignition system checks. Safety precautions and troubleshooting tips are included.
Урьдчилсанview Performance Tool 10-Inch Random Orbital Polisher/Buffer Owner's Manual (W50053)
Owner's manual for the Performance Tool 10-Inch Random Orbital Polisher/Buffer (Model W50053). Provides detailed safety warnings, operating instructions, care and maintenance guidelines, troubleshooting tips, and warranty information for automotive detailing and surface polishing.
Урьдчилсанview Гүйцэтгэлийн хэрэгсэл W2976 Олон хэлний оношлогооны сканнер эзэмшигчийн гарын авлага
This owner's manual provides essential guidance for the Performance Tool W2976 Multilingual Diagnostic Scanner. Learn how to safely operate the device, understand OBD II systems, read and clear diagnostic trouble codes (DTCs), check vehicle compatibility, and interpret readiness monitor status.