Бүтээгдэхүүн дууссанview
The Cartell CP4 Vehicle Sensor Kit is an electronic vehicle detection device designed for automatic gate release. It operates based on the science of electromagnetic induction, detecting the movement of a vehicle to trigger gate operation. This system is supplied with underground burial cable and is specifically designed to respond to vehicles, making it unsuitable as a hold-open loop.
Суурилуулалт ба тохиргоо
Proper installation is crucial for the optimal performance of your Cartell CP4 sensor. Follow these guidelines carefully:
Мэдрэгчийн байршил:
- The sensor is designed to cover a 12-foot wide driveway from the side of the drive.
- Position the sensor approximately 80 to 100 feet from the gate, depending on the length of the supplied cable (available in 100', 200', 300', or 500' lengths).
- Bury the sensor unit and its connecting pipe 3 to 5 inches below the surface.
Figure 1: Installation instructions and diagrams from the back of the product box, detailing sensor placement and wiring.
Кабелийн хамгаалалт:
- Insert the 1/2-inch PVC pipe inside the slip joint of the sensor. Цавуулах хэрэггүй.
- Smooth out the entire length of the cable and gently pull it through a 1/2-inch PVC pipe. This protects the cable underground.
- ЖИЧ: Warranty may be void if the cable is not run in conduit.
Figure 2: The Cartell CP4 sensor unit with its extensive coiled cable, ready for installation.
Зураг 3: Нарийвчилсан view of the Cartell CP4 sensor unit, highlighting its robust design.
Wiring (CP-4):
The CP4 sensor requires a power supply of 8-24 VAC or 8-30 VDC. The current draw is 30-70 µA in standby and 40-60 mA during alarm.
| Утасны өнгө | Dual Exit Terminal | Single Exit Terminal |
|---|---|---|
| Улаан | Эрчим хүч + | Эрчим хүч + |
| Хар | Power - | GND or COM |
| Цагаан | Нийтлэг | GND or COM |
| Цэнхэр | Exit N.O. | Free Exit or Open Terminal |
| Шар | Exit N.C. | (Not used for single exit) |
For single exit terminal setups, the yellow wire is typically not used. Connect the black and white wires to a common ground, the red wire to the positive power supply, and the blue wire to the free exit or open terminal on your gate operator's control board.
Үйл ажиллагааны зарчим
The Cartell CP4 sensor utilizes electromagnetic induction to detect the presence of a vehicle. When a vehicle passes over the buried sensor, it triggers a signal to the gate operator, initiating the gate opening sequence. This system is designed for automatic gate release, providing a convenient exit without requiring manual intervention.
Figure 4: Illustration of a vehicle approaching a gate, demonstrating the sensor's function in triggering the gate to open automatically.
Мэдрэмжийн тохируулга:
In most cases, it is not necessary to adjust the sensor's sensitivity or remove its lid. The sensitivity is set to "High" by default (dip switch in "OFF" position). If adjustment is required, refer to the dip switch settings below:
- High (Default): Detects vehicles going 5 MPH 12-14 feet away. (Dip switches 1 & 2 OFF)
- Дунд: Detects vehicles going 5 MPH 6-8 feet away. (Dip switch 1 ON & 2 OFF)
- Бага: Detects vehicles going 5 MPH 2-3 feet away. (Dip switches 1 & 2 ON)
Засвар үйлчилгээ
The Cartell CP4 sensor is designed for durability and minimal maintenance. Ensure the area around the buried sensor and cable remains clear of heavy debris or obstructions that could interfere with its operation or damage the conduit. Regular visual inspection of exposed wiring and connections is recommended to ensure integrity.
Алдааг олж засварлах
If you encounter issues with your CP4 sensor, first verify all wiring connections according to the diagram in the Setup section. Ensure the sensor is buried at the correct depth and distance from the gate. For more detailed troubleshooting steps, including product issues that may require removing the sensor, please download the full online manual from www.cartell.com эсвэл бүтээгдэхүүний сав баглаа боодол дээр байгаа QR кодыг уншина уу.
For technical support, you may call Cartell at 717-832-0033.
Үзүүлэлтүүд
| Онцлог | Дэлгэрэнгүй |
|---|---|
| Хамгийн их хүрээ | 100 Feet (cable length dependent) |
| Мэдрэгч технологи | Electromagnetic Induction Sensor |
| Шаардлагатай эрчим хүч | 6-31 VAC эсвэл 8-46 VDC |
| Relay Trip Time | 2 секунд |
| Зүйлийн жин | 4.4 фунт |
| Багцын хэмжээ | 16.3 x 8.23 x 3.03 инч |
| Загварын дугаар | CP3-300 |
| Үйлдвэрлэгч | Cartell |
| Өнгө | Хар |
Баталгаат болон дэмжлэг
Cartell provides support for its products. As noted in the installation section, the product warranty may be void if the cable is not run in conduit. For any technical assistance or product inquiries, please contact Cartell directly. You can also find additional resources and the full online manual on the official Cartell webсайт.
- Техникийн дэмжлэг: 717-832-0033
- Албан ёсны Webгарын авлагын сайт: www.cartell.com
