Livex Lighting 2161-02 Outdoor Wall Lantern Instruction Manual

Аюулгүй байдлын чухал мэдээлэл

Please read these instructions carefully before installing or operating your Livex Lighting 2161-02 Outdoor Wall Lantern. Retain this manual for future reference.

АНХААРУУЛГА! ГАЛТАЙЛУУЛАГЧ БУЮУ ХЭЛБЭР ТААСАГЧ ДЭЭР АШИГЛАЛТЫГ УНТРААРАЙ.

This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unsure about any part of the installation, consult a qualified electrician.

Санал 65 Анхааруулга: Энэ бүтээгдэхүүн нь Калифорни мужид хорт хавдар, ургийн гажиг, нөхөн үржихүйн бусад гэмтэл учруулдаг химийн бодис агуулсан байж болзошгүй.

Бүтээгдэхүүн дууссанview

The Livex Lighting 2161-02 is a traditional outdoor wall lantern designed to provide illumination and enhance the aesthetic of your outdoor spaces. It features a polished brass finish and clear beveled glass shades, offering a classic and durable lighting solution.

Image: The Livex Lighting 2161-02 Outdoor Wall Lantern, showcasing its polished brass finish and clear beveled glass panels.

Багцын агуулга

Суулгацыг эхлүүлэхийн өмнө бүх бүрэлдэхүүн хэсгүүд байгаа эсэхийг шалгана уу.

• Fixture body with pre-assembled wiring
• Хөндлөвч
• Суурилуулах эрэг
• Утасны самар
• Glass shades (pre-installed or separate)
• Candle sleeve (if applicable)
• Зургаан өнцөгт самар

Тохиргоо ба суурилуулалт

Before starting, ensure the power is turned off at the circuit breaker or fuse box to prevent electrical shock.

Бэхэлгээ суурилуулах

1. Shut off the power at the circuit breaker and remove any old fixture, including the crossbar.
2. Carefully unpack the new fixture and lay out all parts on a clean, clear surface. Take care not to lose any small parts necessary for installation.
3. Attach the mounting screw part way into the side hole of the crossbar. Then, lock it securely with a hex nut until becoming tight. Attach the crossbar to the junction box using two box screws. The side of the crossbar marked "GND" must face out.
4. Follow wiring instructions carefully (see 'Wiring' section below).
5. l-ийн арын хавтанг хавсарганаamp body (A) onto the junction box, aligning the screws on the crossbar with the mounting holes and locking it securely with the ball nuts (C). Place the candle sleeve (B) over the lamp эзэмшигч.
6. Install the light bulbs in accordance with the fixture's specifications. ДЭЭД ХУГАЦААНЫ WAT-аас хэтэрч болохгүйTAGE ҮНЭЛГЭЭ!
7. With silicone caulking compound, caulk completely around the back of the cover to prevent water from seeping into the outlet box.

Image: Figure 1 - An exploded diagram illustrating the components and assembly sequence for mounting the outdoor wall lantern, including the junction box, supply wire, hex nut, mounting screw, supply ground wire, crossbar, box screw, fixture ground wire, fixture wire, and the main fixture body (A) with candle sleeve (B).

Утас

1. Connect the electrical wires as follows: Connect the black wire from the fixture to the black (hot) wire from the house. Connect the white wire from the fixture to the white (neutral) wire from the house. Make sure all wire nuts are secured.
2. You may wrap the connections with electrical tape. If your outlet box has a ground wire (green or bare copper), connect the fixture's ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the crossbar.
3. Утасны холболтыг хананы уулзвар хайрцагт сайтар оруулаарай.

Image: Figure 2 - A diagram showing standard wiring connections for a light fixture, illustrating how fixture wires (black, white, and ground) connect to house wires (black, white, and ground/bare copper) using wire nuts.

Ашиглалтын заавар

Once installed, restore power at the circuit breaker. The Livex Lighting 2161-02 Outdoor Wall Lantern operates with a standard wall switch (not included). If connected to a compatible dimmer switch, the light output can be adjusted. This fixture is designed for incandescent bulbs and is dimmable with appropriate dimming controls.

Засвар үйлчилгээ

Цэвэрлэгээ

To maintain the finish and appearance of your fixture, clean it regularly with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or polishes as they may damage the finish. For glass panels, use a mild glass cleaner applied to a cloth, not directly to the fixture.

Булцуу солих

Always turn off the power at the circuit breaker before replacing bulbs. Allow bulbs to cool completely before touching them. Use only bulbs that meet the specified wattage and type (E26 base, up to 100 watts incandescent). Exceeding the maximum wattage can cause overheating and damage to the fixture.

Алдааг олж засварлах

• Гэрэл асахгүй байна:
  • Хэлхээ таслагч дээр цахилгаан асаалттай байгаа эсэхийг шалгана уу.
  • Чийдэнг залгуурт найдвартай шургуулсан бөгөөд шатаагүй эсэхийг шалгаарай.
  • Verify all wire connections are secure and correctly made.
• Гэрэл анивчих:
  • Чийдэнг бүрэн чангалсан эсэхийг шалгаарай.
  • Сул утсан холболт байгаа эсэхийг шалгана уу.
  • If using a dimmer, ensure it is compatible with incandescent bulbs and the bulb itself is dimmable.
• Glass panels are loose:
  • Carefully inspect the fixture for any retaining clips or screws that may need tightening.

Үзүүлэлтүүд

Баталгаат хугацааны мэдээлэл

This Livex Lighting fixture comes with a 1-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For specific warranty details and limitations, please contact Livex Lighting customer service.

Дэмжлэг

For further assistance, technical support, or to inquire about replacement parts, please visit the official Livex Lighting store or contact their customer service department.

Livex Lighting Store: Livex Lighting on Amazon