Танилцуулга
This manual provides essential instructions for the setup, operation, and maintenance of your Pro-Ject RM 1.3 Turntable. Please read it thoroughly before use to ensure proper functionality and longevity of your device.
Багцын агуулга
Before proceeding with the setup, please verify that all components are present:
- Pro-Ject RM 1.3 Turntable Unit
- Плиттер
- Жолоо барих
- Outboard 15V AC Motor
- Эрчим хүчний хангамж
- Sumiko Pearl Cartridge (pre-installed or separate)
- Removable RCA Cables
- Эсрэг жин
- Тэшүүрийн эсрэг жин
- Stylus даралт хэмжигч
Тохируулах заавар
Follow these steps carefully to set up your turntable:
- Савлах: Carefully remove all components from the packaging. Retain packaging for future transport.
- Таваг суурилуулах: Place the platter onto the central spindle. Ensure it sits securely and rotates freely.
- Моторын байршил: Position the outboard motor unit next to the turntable chassis. The motor pulley should align with the outer rim of the platter.
- Drive Belt Installation: Gently stretch the drive belt around the motor pulley and the outer rim of the platter. Ensure the belt is not twisted.
- Cartridge Installation (if not pre-installed): If your Sumiko Pearl cartridge is not pre-installed, carefully attach it to the tonearm headshell using the provided screws. Ensure correct alignment.
- Эсрэг жингийн тохируулга: Slide the counterweight onto the rear of the tonearm. Adjust it until the tonearm floats horizontally. Then, set the tracking force according to the cartridge manufacturer's recommendations (typically 1.8g for Sumiko Pearl). Use a stylus pressure gauge for accuracy.
- Anti-skating Adjustment: Attach the anti-skating weight to the tonearm's anti-skating mechanism. Adjust the setting to match the tracking force.
- -д холбогдож байна Ampамь нас: Connect the removable RCA cables from the turntable's output to the "Phono" input of your amplifier or a dedicated phono preamplifier. Ensure the ground wire is connected between the turntable and your ampилүү урт/өмнөхampдууг багасгахын тулд өргөгч.
Ашиглалтын заавар
- Асаах: Connect the power supply to the motor unit and a wall outlet. Press the power button on the motor unit to start the platter rotation.
- Хурд сонгох: Most turntables offer 33 1/3 RPM and 45 RPM. Ensure the correct speed is selected for your record. (Refer to motor unit for speed selection mechanism, typically a switch or belt position change).
- Байрны бичлэг: Carefully place your vinyl record onto the platter.
- Доод гар: Gently lift the tonearm using the cueing lever. Position the stylus over the desired track on the record. Slowly lower the cueing lever to allow the stylus to descend onto the record groove.
- Тоглуулах: The record will now play. Adjust the volume on your ampнастан.
- Тоглуулахыг зогсоох: At the end of the record, or when you wish to stop, use the cueing lever to lift the tonearm from the record. Return the tonearm to its rest and secure it. Press the power button on the motor unit to stop the platter.
Засвар үйлчилгээ
- Бичлэг цэвэрлэх: Regularly clean your vinyl records using a dedicated record brush or cleaning solution to remove dust and static.
- Stylus арчилгаа: Use a soft stylus brush to gently clean the stylus tip before and after each play. Brush from back to front. Avoid touching the stylus with your fingers.
- Эргүүлдэг тавцан цэвэрлэх: Wipe the turntable chassis and platter with a soft, dry, lint-free cloth. Avoid abrasive cleaners or solvents.
- Туузны үзлэг: Periodically check the drive belt for wear or stretching. Replace if necessary to maintain accurate playback speed.
Алдааг олж засварлах
Хэрэв та эргэлдэгч тавцантайгаа холбоотой асуудалтай тулгарвал дараах нийтлэг асуудал болон шийдлүүдийг үзнэ үү.
| Асуудал | Боломжит шалтгаан | Шийдэл |
|---|---|---|
| No power / Platter not spinning | Power cable disconnected; faulty power supply/motor; power outlet issue. | Ensure power cable is securely connected. Test the power outlet with another device. If the issue persists, contact support. |
| Хувцаслах эсвэл дуугарах чимээ | Ground wire not connected; proximity to other electronics; faulty cabling; internal wiring issue. | Ensure the ground wire is securely connected between the turntable and ampилүү урт/өмнөхamplifier. Move the turntable away from other electronic devices. Check RCA cables for damage. If hum persists, it may indicate an internal grounding issue requiring professional service. |
| Distorted sound / Skipping | Incorrect tracking force; worn or dirty stylus; damaged record; incorrect anti-skating. | Re-adjust tracking force and anti-skating. Clean the stylus. Inspect the record for damage. Replace stylus if worn. |
| Буруу тоглуулах хурд | Incorrect speed selection; worn or stretched drive belt. | Verify the correct speed setting. Inspect and replace the drive belt if it appears worn or loose. |
Үзүүлэлтүүд
| Онцлог | Дэлгэрэнгүй |
|---|---|
| Брэнд | Pro-Ject |
| Загвар | RM 1.3 |
| Бүтээгдэхүүний хэмжээс | 15 x 4.33 x 13.78 инч |
| Зүйлийн жин | 11.15 фунт |
| Оруулсан бүрэлдэхүүн хэсгүүд | Sumiko Pearl Cartridge, removable RCA cables |
| Моторын төрөл | Хувьсах гүйдлийн мотор |
| Дохионы формат | Аналог |
| Ботьtage | 15 вольт (AC) |
| Өнгө | Хар |
Баталгаат болон дэмжлэг
For warranty information, please refer to the documentation provided with your purchase or visit the official Pro-Ject website. For technical support or service inquiries, please contact your authorized Pro-Ject dealer or the manufacturer's customer service department.
Баталгаат нэхэмжлэл гаргахын тулд худалдан авалтаа нотлох баримтаа хадгалаарай.
