1. Танилцуулга
This manual provides detailed instructions for the safe and efficient use of your DROK DC-DC Buck Converter. This module is designed to step down a higher DC input voltage to a lower, adjustable DC output voltage, featuring an LCD display for real-time monitoring of voltage, гүйдэл ба хүч.
2. Бүтээгдэхүүний онцлог
- Wide Input Voltage хүрээ: DC 6.5V - 36V.
- Тохируулах боломжтой гаралтын хэмжээtage: DC 1.2V to 32V. Factory default output is 5V.
- High Output Current: Stable operation at 3.5A for extended periods, capable of reaching 4.5A with adequate heat dissipation. Adjustable current limit is approximately 4.2A-4.5A.
- LCD дэлгэц: Оруулсан ботыг харуулнаtage, гаралтын ботьtage, гаралтын гүйдэл ба гаралтын чадал.
- Дэлгэцийн өндөр нягтрал: Ботьtage resolution of 0.05V, current resolution of 0.005A.
- Дэлгэцийн нарийвчлал: Ботьtage display accuracy of ±0.1V, current display accuracy of ±0.05A.
- Товчлуурын удирдлага: Easy adjustment of output voltage and control of output ON/OFF state without a screwdriver.
- Input Reverse Connection Protection: Protects the module from damage due to incorrect input polarity.
- Хамгаалалтын Casing: Includes a transparent acrylic case to prevent physical damage to the module.
3. Аюулгүй байдлын урьдчилан сэргийлэх арга хэмжээ
- Боть зөв оруулсан эсэхийг шалгаарайtage polarity. The module has input reverse connection protection, but always verify connections.
- Байна no reverse current protection on the output terminals. Do not connect a battery or other power source to the output without an external diode to prevent reverse current flow, as this can damage the module.
- Do not short-circuit the Input IN- terminal to the Output OUT- terminal. This will disable the constant current function.
- Ensure proper ventilation, especially when operating at higher currents (above 3.5A) to allow for adequate heat dissipation.
- Always verify the output voltage setting before connecting any load to prevent damage to your devices.
- Handle the module with care, especially during assembly of the acrylic case, to avoid damage to components.
4. Техникийн үзүүлэлтүүд
| Параметр | Үнэ цэнэ |
|---|---|
| Оролтын хэмжээtage Хамрах хүрээ | DC 6.5V - 36V |
| Гаралтын ботьtage Хамрах хүрээ | DC 1.2V - 32V (Adjustable) |
| Output Current (Stable) | 3.5 А |
| Output Current (Max with Heat Dissipation) | 4.5 А |
| Гаралтын хүч | 75 Вт |
| Ботьtage Дэлгэцийн нягтрал | 0.05 В |
| Одоогийн дэлгэцийн нягтрал | 0.005 А |
| Ботьtage Дэлгэцийн нарийвчлал | ±0.1V |
| Current Display Accuracy | ± 0.05А |
| Хэмжээ | 14.7 x 8 x 5.2 см |
| Жин | 70 гр |
5. Тохиргоо
5.1 Бүрэлдэхүүн хэсгүүдийн тодорхойлолт
Familiarize yourself with the components of the buck converter module:
Figure 1: Component layout of the DROK buck converter. Labels indicate input/output terminals, LCD display, control buttons, and the voltage тохируулгын потенциометр.
5.2 Acrylic Case Assembly
The module comes with a transparent acrylic case for protection. Assembly is straightforward:
- Identify the top and bottom acrylic plates, standoffs, and screws.
- Carefully align the bottom acrylic plate with the mounting holes on the PCB.
- Insert the brass standoffs through the bottom plate and into the PCB.
- Place the top acrylic plate over the standoffs, ensuring all cutouts align with the module's components (terminals, buttons, screen).
- Secure the top plate with the remaining screws. Do not overtighten.
Figure 2: Disassembled module with acrylic case components.
Figure 3: Assembled module with protective case.
5.3 утас холболт
Connect your power source and load to the module using the screw terminals:
- Input (IN+ / IN-): Connect your DC power source (6.5V-36V) to these terminals. Ensure correct polarity: IN+ for positive, IN- for negative.
- Output (OUT+ / OUT-): Connect your load to these terminals. Ensure correct polarity: OUT+ for positive, OUT- for negative.
Note: Always double-check wiring before applying power.
6. Ашиглалтын заавар
6.1 Асаах/унтраах
- After connecting the input power, the LCD will light up.
- дээр дарна уу ON/OFF button (usually on the left side) to toggle the output power.
- To set the default power-on state (output ON or OFF), press and hold the ON/OFF button. The module will remember this setting for subsequent power cycles.
6.2 Adjusting Output Voltage
Гаралтын эзлэхүүнtage is adjusted using the two buttons on the right side of the module:
- дээр дарна уу '+' button to increase the output voltage.
- дээр дарна уу '-' button to decrease the output voltage.
- The LCD will display the current output voltage during adjustment.
6.3 LCD Display Modes
The module features an LCD that can display various parameters. Use the button on the left (often labeled 'IN/OUT' or similar) to cycle through display modes:
- Гаралтын ботьtage (OUT V): Displays the current output voltage.
- Оролтын хэмжээtage (IN V): Displays the current input voltage.
- Оролт/гаралтын ботьtage (IN/OUT V): Alternates between input and output voltage дэлгэц.
- Output Current (OUT A): Displays the current flowing through the output.
- Output Power (OUT W): Displays the calculated output power.
Зураг 4: Гаралтын хэмжээtage Дэлгэц
Зураг 5: Оролтын хэмжээtage Дэлгэц
Figure 6: Input/Output Voltage Дэлгэц
Figure 7: USB Output Voltage Display (if applicable)
6.4 Constant Current (CC) Adjustment
The module supports constant current output. The current limit can be adjusted using the small potentiometer (ADJ-I) on the board. Turn clockwise to increase the current limit. This is typically set to approximately 4.2A-4.5A at the factory.
7. Засвар үйлчилгээ
- Модулийг цэвэр, тоос шороо, хог хаягдлаас цэвэр байлга. Цэвэрлэхэд зөөлөн, хуурай даавуу ашиглаарай.
- Ensure adequate airflow around the module, especially when operating at higher loads, to prevent overheating.
- Regularly check wiring connections for tightness and signs of wear or corrosion.
- Модулийг чийг, хэт өндөр температур, идэмхий орчинд өртөхөөс зайлсхий.
8. Алдаа засах
| Асуудал | Боломжит шалтгаан | Шийдэл |
|---|---|---|
| No display/No output | No input power; Incorrect input polarity; Output turned off. | Check input power connections; Verify input polarity; Press the ON/OFF button to enable output. |
| Гаралтын ботьtage-г тохируулах боломжгүй | Potentiometer at its limit; Faulty potentiometer. | Ensure the adjustment buttons are being pressed correctly; If still unresponsive, contact support. |
| Constant current function not working | Input IN- short-circuited to Output OUT-. | Check wiring to ensure IN- and OUT- are not connected. |
| Модулийн хэт халалт | Excessive load current; Insufficient ventilation. | Reduce load current; Ensure adequate airflow around the module; Consider adding a fan for continuous high-current operation. |
9. Бүтээгдэхүүний видео
Watch these official videos for additional guidance on using your DROK Buck Converter:
Video 1: Demonstration of the buck converter's features and operation.
Video 2: Detailed guide on setting up and adjusting the output voltage.
Видео 3: Богино бичлэгview of the module's display functions.
Video 4: Comprehensive tutorial on advanced usage and applications.
10. Баталгаат хугацаа ба дэмжлэг
For warranty information or technical support, please refer to the product packaging or contact your retailer. Keep your purchase receipt for warranty claims.
