Танилцуулга
This manual provides essential instructions for the safe installation, operation, and maintenance of the Hubbell 7051-G 15A, 125V-AC, 2-Pole, 3-Wire Receptacle. Please read this manual thoroughly before installation and retain it for future reference. Proper installation by a qualified electrician is recommended.
Аюулгүй байдлын мэдээлэл
АНХААРУУЛГА: Risk of electric shock or fire. Improper installation can result in serious injury or death. Always turn off power at the circuit breaker or fuse box before installing or servicing this device. Use only copper wire with this device. Do not use with aluminum wire unless specifically rated for it. Ensure all connections are tight and secure.
- Цахилгаан хэлхээн дээр ажиллахын өмнө цахилгааныг үргэлж салга.
- Хэрэв та суулгах процессын аль нэг хэсэгт эргэлзэж байвал мэргэшсэн цахилгаанчинтай зөвлөлд.
- Орон нутгийн болон үндэсний цахилгааны бүх дүрмийг дагаж мөрдөөрэй.
- Төхөөрөмжийн тогтоосон цахилгааны үзүүлэлтээс хэтрүүлж болохгүй.
Бүтээгдэхүүн дууссанview
The Hubbell 7051-G is a 15 Amp, 125 Volt, 2-pole, 3-wire grounding duplex receptacle designed for general-purpose electrical applications. It features a durable nylon construction and is suitable for various residential and commercial installations.
Зураг: Урд view of the Hubbell 7051-G duplex receptacle, showing two outlets with grounding slots.
Тохиргоо ба суурилуулалт
Шаардлагатай хэрэгслүүд: Screwdriver (Phillips and/or flathead), Wire Strippers, Voltage Шалгагч.
- Цахилгааныг унтраах: Locate the circuit breaker or fuse that controls the outlet you are working on and turn it off. Verify power is off using a voltage шалгагч.
- Хуучин савыг ав (хэрэв байгаа бол): Unscrew the wall plate and then the mounting screws holding the old receptacle in the electrical box. Carefully pull the receptacle out and disconnect the wires.
- Утас бэлтгэх: Strip approximately 1/2 inch of insulation from the ends of the circuit wires. Ensure the wire ends are clean and straight.
- Холбох утас:
- Ногоон эсвэл нүцгэн зэс утас (газардуулга): Connect to the green grounding screw.
- Цагаан утас (төвийг сахисан): Connect to the silver screw.
- Black or Red Wire (Hot/Live): Connect to the brass screw.
- Холбох сав: Утастай савыг цахилгаан хайрцаг руу болгоомжтой түлхэнэ үү. Үүнийг өгөгдсөн эрэг шургаар бэхлэнэ.
- Ханын хавтанг суурилуулах: Чимэглэлийн ханын хавтанг савны дээгүүр холбоно.
- Эрчим хүчийг сэргээх: Turn the power back on at the circuit breaker or fuse box. Test the receptacle with a known working device.
Зураг: хажуу тал view of the Hubbell 7051-G receptacle, showing the strip gauge for proper wire preparation.
Зураг: Буцах view of the Hubbell 7051-G receptacle, illustrating the screw terminals for wiring connections (brass for hot, silver for neutral, green for ground).
Image: Close-up of the rear of the Hubbell 7051-G receptacle, detailing the wire strip gauge and voltage ratings (15A, 125V and 10A, 250V).
Ашиглалтын заавар
To operate the Hubbell 7051-G receptacle, simply insert the plug of your electrical device into one of the two available outlets. Ensure the plug is fully inserted. The receptacle is designed for standard 2-prong or 3-prong grounded plugs.
Зураг: Урд view of the Hubbell 7051-G receptacle, ready for device plugs.
Засвар үйлчилгээ
The Hubbell 7051-G receptacle requires minimal maintenance. Periodically inspect the receptacle and wall plate for any signs of damage, cracks, or discoloration. If any damage is observed, turn off power at the circuit breaker and replace the receptacle immediately. Clean the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
Алдааг олж засварлах
- No Power at Receptacle:
- Check the circuit breaker or fuse for the circuit. Reset the breaker or replace the fuse if tripped/blown.
- Ensure all wire connections are secure. Turn off power before checking connections.
- Савыг томоор шалганаtage tester to confirm power presence.
- Loose Plug Connection:
- If plugs do not stay firmly in the receptacle, the internal contacts may be worn. The receptacle should be replaced by a qualified electrician.
- Хэт халалт:
- If the receptacle feels warm to the touch, immediately disconnect all devices and turn off power. This could indicate an overload or a faulty connection. Consult a qualified electrician.
Үзүүлэлтүүд
| Брэнд | Хаббелл |
| Загвар | 7051-Г |
| Ampарилгах | 15 Amps |
| Ботьtage | 125 вольт |
| Туйл/утас | 2 туйлт, 3 утастай газардуулга |
| Материал | Нейлон |
| Бүтээгдэхүүний хэмжээс | 4.25 x 2 x 1.5 инч |
| Үйлдвэрлэгч | HUBBELL |
Image: The Hubbell 7051-G receptacle shown in its original product box.
Image: Barcode label for the Hubbell 7051-G 2P 3W 15A 125V-AC Receptacle, showing product identification details including UPC 0129190665219.
Баталгаат болон дэмжлэг
Specific warranty information for the Hubbell 7051-G Receptacle is not provided within this manual. For warranty details or technical support, please contact Hubbell customer service directly or visit their official webсайт. Худалдан авалтын баримтаа худалдан авалтын баталгаа болгон хадгалаарай.
Үйлдвэрлэгч: HUBBELL
Webсайт: www.hubbell.com (Жишээ ньample холбоос, бодит холбоос өөр байж болно)
