1. Танилцуулга
The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.
Зураг 1.1: Урд view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.
2. Аюулгүй байдлын мэдээлэл
- Суулгах, ажиллуулахын өмнө бүх зааврыг анхааралтай уншина уу.
- Эрчим хүчний хангамжийн хэмжээг баталгаажуулна ууtage нь төхөөрөмжийн шаардлагад нийцэж байна (85-265V AC, 50/60Hz).
- All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
- Төхөөрөмжийг хэт их чийг, тоос шороо эсвэл идэмхий хийтэй орчинд бүү ажиллуул.
- Засвар үйлчилгээ хийх эсвэл утсыг солихын өмнө цахилгааныг салга.
- Keep the device away from strong electromagnetic interference.
3. Бүтээгдэхүүний онцлог
- Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
- Dual digital display for Process Value (PV) and Set Value (SV).
- Multiple control outputs: Relay and SSR (Solid State Relay).
- Alarm functions (AL1, AL2) for high/low limits.
- PID auto-tuning function for precise control.
- Wide operating temperature range.
- Compact and easy-to-install design.
4. Багцын агуулга
- 1 x SINOTIMER MC101-611 Temperature Control Meter
- 1 x Mounting Bracket (as shown in Figure 4.1)
- 1 х хэрэглэгчийн гарын авлага (энэ баримт бичиг)
Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.
5. Тохиргоо
5.1 Суурилуулалт
The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.
5.2 Утас
Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.
- 1 ба 2-р терминалууд: AC Power Supply (85-265V AC, 50/60Hz)
- 3 ба 4-р терминалууд: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
- 6 ба 7-р терминалууд: Alarm Output (ALM) - Relay contacts for alarm.
- Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
- 11 ба 12-р терминалууд: SSR Output - For connecting to a Solid State Relay.
Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.
6. Ашиглалтын заавар
6.1 Дээд дэлгэцview
The meter features a dual display:
- PV (Үйл явцын утга): The upper red display shows the current measured temperature/humidity.
- SV (Тохируулсан утга): The lower green display shows the desired set point.
- OUT үзүүлэлт: Illuminates when the main output is active.
- AT үзүүлэлт: Illuminates when the auto-tuning function is active.
- AL1/AL2 үзүүлэлтүүд: Illuminate when Alarm 1 or Alarm 2 conditions are met.
6.2 Товчлуурын функцууд
- SET товчлуур: Used to enter parameter setting mode and confirm selections.
- < / R/S Button: Used to shift digits during setting or to reset alarms.
- ▼ (Доош) Товч: Decreases the value of a parameter or set point.
- ▲ (Дээш) Товч: Increases the value of a parameter or set point.
6.3 Setting the Temperature/Humidity Set Point (SV)
- Хэвийн ажиллагааны горимд товчийг дарна уу SET button once. The SV display will begin to flash.
- -г ашиглана уу ▲ (Дээш) ба ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
- дээр дарна уу SET button again to confirm the new SV and exit the setting mode.
6.4 Advanced Parameter Settings
To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the SET button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Дээш) ба ▼ (Down) buttons to navigate through parameters and the SET button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.
7. Засвар үйлчилгээ
- Цэвэрлэгээ: Дэлгэцийг арчиж, casing зөөлөн, хуурай даавуугаар. Зүлгүүрийн цэвэрлэгч, уусгагчийг бүү ашигла.
- Шалгалт: Утасны холболтыг сул эсвэл зэврэлттэй эсэхийг үе үе шалгаж байгаарай.
- Хадгалах: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.
8. Алдаа засах
| Асуудал | Боломжит шалтгаан | Шийдэл |
|---|---|---|
| Дэлгэц хоосон байна | No power supply; Incorrect wiring; Device fault. | Цахилгааны холболт болон боть шалгахtage; Verify wiring according to diagram; Contact support if problem persists. |
| PV дэлгэц дээр 'HHHH' эсвэл 'LLLL' гэж гарч ирнэ | Sensor open circuit (HHHH) or short circuit (LLLL); Sensor not connected; Incorrect sensor type setting. | Check sensor wiring; Ensure sensor is connected; Verify sensor type setting in parameters matches connected sensor. |
| Гаралт идэвхжихгүй байна | SV not reached; Control mode incorrect; Output wiring issue. | Adjust SV; Check control mode (e.g., heating/cooling); Verify output wiring. |
| Температурын заалт буруу байна | Sensor calibration needed; Sensor damaged; External interference. | Perform sensor calibration (if supported); Replace sensor; Relocate device away from interference sources. |
9. Техникийн үзүүлэлтүүд
Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.
| Параметр | Үнэ цэнэ |
|---|---|
| Загвар | MC101-611 |
| Хүрээ | 0-1300°C K (Configurable for various sensor types) |
| Температурын нэгж | Celsius/Fahrenheit (Selectable) |
| Гаралт | Relay/SSR |
| Сэрүүлэг | АЛМ1 |
| Нийлүүлэлт ботьtage | 85-265V хувьсах гүйдэл, 50/60Гц |
| Дэлгэцийн төрөл | LCD |
| Зүйлийн жин | 5.1 унц |
| Багцын хэмжээ | 3.9 x 2.8 x 2.4 инч |
10. Баталгаат хугацаа ба дэмжлэг
This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webхолбоо барих мэдээлэл авах сайт.
