Танилцуулга
This manual provides comprehensive instructions for the safe and effective use of the Valefod LM2596 DC-DC Buck Converter with LED Display. This module is designed to step down a DC input voltage to a lower, adjustable DC output voltage, featuring an integrated LED display for real-time voltage хяналт.
Image 1: Three Valefod LM2596 DC-DC Buck Converter modules.
Аюулгүй байдлын мэдээлэл ба чухал тэмдэглэл
- Оролтын хэмжээtage Шаардлага: Оролтын эзлэхүүнtage нь хүссэн гаралтын хэмжээнээс дор хаяж 1.5V-ээр өндөр байх ёстойtage. This module is a buck (step-down) converter and cannot boost voltage.
- Туйлшрал: Ensure correct polarity when connecting input and output wires. Do not reverse the input and output interfaces to prevent damage to the module.
- Output Current/Power: Keep the output current under 2A (or 15W). For prolonged operation at higher loads, a heat sink is recommended to prevent overheating.
- Цахилгааны аюулгүй байдал: Always disconnect power before making any connections or adjustments. Exercise caution when working with electrical circuits.
Бүтээгдэхүүний онцлог
- DC-DC step-down module with integrated LED digital voltmeter.
- Thickened circuit boards and advanced solid-state capacitors for stable performance.
- Short circuit and over-temperature protection.
- Тохируулах боломжтой гаралтын ботьtage via a multi-turn potentiometer.
- Display can show either input or output voltage.
Зураг 2: Ойролцоогоор view of a single LM2596 module.
Тохиргоо ба холболтууд
Before connecting the module, ensure all power sources are disconnected.
- Терминалуудыг тодорхойлох: Locate the "IN+" (Input Positive), "IN-" (Input Negative), "OUT+" (Output Positive), and "OUT-" (Output Negative) screw terminals on the module.
- Оролтын холболт: Connect your DC power source to the "IN+" and "IN-" terminals. Ensure the positive lead of your power source connects to "IN+" and the negative lead to "IN-".
- Гаралтын холболт: Connect your load (the device requiring regulated voltage) to the "OUT+" and "OUT-" terminals. Ensure the positive lead of your load connects to "OUT+" and the negative lead to "OUT-".
- Анхны ботьtage Тохируулга: Before applying power to your load, it is recommended to pre-adjust the output voltage. Connect a multimeter to the output terminals and adjust the potentiometer until the desired voltage гарч ирнэ.
Image 3: Module layout and connection points.
Ашиглалтын заавар
Ботьtage Тохируулга
Гаралтын эзлэхүүнtage is adjusted using the blue multi-turn potentiometer located on the module.
- Use a small screwdriver to turn the screw on the potentiometer.
- Эргэх цагийн зүүний дагуу will generally нэмэгдүүлэх гаралтын ботьtage.
- Эргэх цагийн зүүний эсрэг will generally буурах гаралтын ботьtage.
- Жич: The factory default setting often results in a high output voltage. You may need to turn the potentiometer counter-clockwise approximately 7-15 full rotations before the voltage begins to decrease. Each full rotation typically adjusts the voltage by about 1V.
Digital Voltmeter Operation
The integrated LED display provides real-time voltage уншилтууд.
- ON/OFF Button (Left Button):
- Богино хэвлэлийн: Toggles the digital voltmeter display ON or OFF.
- Long Press (>1s, <4s): Shuts down the digital voltmeter display.
- Long Press (>4s): Enters voltage measurement self-calibration mode (see Calibration section).
- Mode Button (Right Button):
- Богино хэвлэлийн: Switches the display between input voltage ("IN" indicator light) and output voltage ("OUT" indicator light).
- Long Press (>2s): Used during calibration to switch between input and output calibration, and to save calibrated values.
Voltmeter Calibration (Optional)
This procedure is for users requiring highly accurate voltage readings from the integrated voltmeter. The factory setting is 0.0V deviation.
- Шалгалт тохируулгын горимыг оруулна уу: With the module powered on, long press the left "ON/OFF" button for more than 4 seconds. The "IN" indicator light will illuminate, signifying input voltage measurement calibration has started. The display will show a calibration value (e.g., "0.0").
- Calibrate Input Voltage: Connect a precise external voltmeter to the input terminals. Compare the reading on the module's display with the external voltmeter.
- Tap the left button to decrease the displayed value.
- Tap the right button to increase the displayed value.
- Each tap adjusts by a small unit (less than 0.1V). You may need to tap 1-5 times to see a 0.1V change. Adjust until the module's display matches your external voltmeter.
- Switch to Output Calibration: After calibrating the input voltage, long press the right "Mode" button for more than 2 seconds. The "OUT" indicator light will illuminate, signifying output voltage measurement calibration has started.
- Гаралтын боть тохируулга хийхtage: Connect a precise external voltmeter to the output terminals. Compare the reading on the module's display with the external voltmeter.
- Tap the left button to decrease the displayed value.
- Tap the right button to increase the displayed value.
- Adjust until the module's display matches your external voltmeter.
- Save Calibration: After calibrating both input and output, long press the right "Mode" button for more than 2 seconds. The adjusted values will be saved (retained even after power loss), and the module will return to normal voltage дэлгэцийн горим.
Үзүүлэлтүүд
| Онцлог | Дэлгэрэнгүй |
|---|---|
| Загвар | LM2596 / Digital Tube Voltmeter |
| Оролтын хэмжээtage | DC 4V - 40V |
| Гаралтын ботьtage | DC 1.5V - 35V (adjustable) |
| Гаралтын гүйдэл | 3А (хамгийн их) |
| Хөрвүүлэлтийн үр ашиг | 92% (дээд тал нь) |
| Шилжүүлэгч давтамж | 150 кГц |
| Ашиглалтын температур | -45 хэмээс +85 хэм хүртэл |
| Хэмжээ (L x W x H) | 57 мм x 36 мм x 13 мм |
| Жин | 21g per module |
Image 4: Module dimensions.
Алдааг олж засварлах
- Гаралтгүй Ботьtage / Display Off:
- Check input power supply connections and ensure it is within the 4V-40V range.
- Verify input polarity.
- Ensure the left "ON/OFF" button has been short-pressed to activate the display.
- Гаралтын ботьtage Not Adjusting:
- Оролтын эзлэхүүнийг баталгаажуулна ууtage is at least 1.5V higher than the desired output.
- Turn the potentiometer counter-clockwise multiple rotations (7-15) as the default setting might be at maximum voltage.
- Ensure the potentiometer is not damaged.
- Модулийн хэт халалт:
- Reduce the output current or power draw.
- Модулийн эргэн тойронд хангалттай агааржуулалтыг хангах.
- Consider adding a heat sink if operating continuously near the maximum current/power limits (2A or 15W).
- Вольтметрийн заалт буруу байна:
- Perform the voltmeter calibration procedure detailed in this manual.
- Ensure connections to the external multimeter are secure and accurate during calibration.
Засвар үйлчилгээ
The Valefod LM2596 module requires minimal maintenance.
- Модулийг цэвэр, тоос шороо, хог хаягдлаас цэвэр байлга.
- Avoid exposing the module to excessive moisture or extreme temperatures outside its operating range.
- Periodically check connections for tightness and ensure no wires are frayed or damaged.
Баталгаат болон дэмжлэг
For warranty information or technical support, please refer to the product's purchase platform or contact Valefod customer service directly. Please have your model number (LM2596 / VA-0162-BL) and purchase details available when contacting support.
