Offgridtec MPPT Pro Duo Charge Controller 30A 12V/24V Instruction Manual

1. Танилцуулга

Thank you for choosing the Offgridtec MPPT Pro Duo charge controller. This device is designed to efficiently manage solar power input to charge two independent battery banks, typically a main service battery and a starter battery, in 12V or 24V systems. It utilizes Maximum Power Point Tracking (MPPT) technology to optimize energy harvest from your solar panels. Please read this manual thoroughly before installation and operation to ensure safe and optimal performance.

Зураг 1: Урд view of the Offgridtec MPPT Pro Duo Charge Controller.

2. Аюулгүй ажиллагааны заавар

Always observe the following safety precautions to prevent personal injury or damage to the controller and connected equipment:

• Суурилуулалтыг зөвхөн мэргэшсэн ажилтан гүйцэтгэнэ.
• Ensure all power sources (solar panels, batteries) are disconnected before installation or maintenance.
• Тохиромжтой багаж хэрэгсэл ашиглаж, хамгаалалтын хувцас өмс.
• Do not disassemble or attempt to repair the controller. Contact Offgridtec support for assistance.
• Хэт халалтаас урьдчилан сэргийлэхийн тулд хянагчийн эргэн тойронд зохих агааржуулалтыг хангана.
• Connect batteries with correct polarity. Reverse polarity can cause severe damage.
• Use fuses or circuit breakers on all battery and solar panel connections as recommended by local regulations and system design.
• Avoid short-circuiting battery terminals or solar panel wires.
• Keep the controller away from flammable materials, moisture, and direct sunlight.

3. Бүтээгдэхүүн дууссанview

3.1 Гол онцлогууд

• Dual battery charging: Charges both main (service) and starter batteries.
• MPPT Technology: Maximizes power harvest from solar panels.
• Supports 12V and 24V systems.
• Maximum charge current up to 30A.
• Adaptive three-level charging for extended battery life.
• Supports various battery types: Gel, Flooded, LiFePO4, Li-NiCoMn (for main battery).
• Secondary charge output for starter battery (supports lead-acid).
• Optional remote display and Bluetooth compatibility (accessories required).
• AES control signal for car refrigerators to prevent energy waste.
• Standard bus protocol and RS485 communication connection.
• Robust aluminum heatsink design for efficient cooling.
• Overload, reverse polarity, and deep discharge protection.

3.2 Бүрэлдэхүүн хэсэг

The Offgridtec MPPT Pro Duo charge controller includes:

• MPPT Pro Duo Charge Controller unit.
• Холболтын терминалууд.
• Integrated LED status indicators.
• SET button for battery type selection.
• Temperature sensor ports (one with integrated sensor, one for external).
• RS485 холбооны порт.
• AES signal output port.

Зураг 2: Урд ба хойд view of the charge controller, highlighting the heatsink design.

4. Тохиргоо ба суурилуулалт

Proper installation is crucial for the safe and efficient operation of your charge controller. Ensure all safety instructions are followed.

4.1 Холбох байршил

• Mount the controller vertically on a non-flammable surface.
• Ensure adequate air circulation around the heatsink for optimal cooling.
• Avoid locations exposed to direct sunlight, high temperatures, or moisture.
• Dimensions: 24.7 cm (L) x 16.5 cm (W) x 6.9 cm (H).
• Mounting holes diameter: 5 mm.

Figure 3: Physical dimensions of the MPPT Pro Duo charge controller, showing the aluminum heatsink.

4.2 Утасны диаграмм ба холболтууд

Follow the wiring sequence below. Incorrect wiring can damage the controller or batteries.

1. Connect Battery 1 (Main/Service Battery): Connect the positive and negative terminals of your main battery to the BATT1 terminals on the controller. Use appropriate cable gauge (e.g., 16 mm² / AWG6). Ensure correct polarity.
2. Connect Battery 2 (Starter Battery): Connect the positive and negative terminals of your starter battery to the BATT2 terminals on the controller. Use appropriate cable gauge (e.g., 4 mm² / AWG12). Ensure correct polarity.
3. Connect Solar Panels (PV): Connect the positive and negative terminals of your solar panel array to the PV terminals on the controller. Ensure the open-circuit voltagТаны нарны хавтангийн хүчдэл 100В-оос хэтрэхгүй байна.
4. Connect Temperature Sensors: The controller includes ports for temperature sensors. Connect the provided sensor to monitor battery temperature for optimized charging.
5. Нэмэлт холболтууд:
   • RS485 харилцаа холбоо: For connecting an optional remote display or USB adapter for PC communication.
   • AES Signal Output: For controlling car refrigerators to prevent excessive discharge of the main battery.
6. Газардуулга: Ensure the controller is properly grounded (negative grounding).

Figure 4: Simplified wiring diagram showing connections from solar panel to controller and dual batteries.

Зураг 5: Жишээ ньample installation of the charge controller in a recreational vehicle.

5. Ашиглалтын заавар

5.1 Анхдагч асаалт

After all connections are securely made, connect the battery power first, then the solar panel power. The controller will perform a self-test, and the LED indicators will illuminate.

5.2 Setting Battery Type (BATT1)

The controller supports various battery types for the main battery (BATT1). To select the correct battery type:

1. -г удаан дар SET button for approximately 5 seconds until the battery type indicator starts flashing.
2. дээр дарна уу SET button repeatedly to cycle through the available battery types (Gel, Flooded, LiFePO4, Li-NiCoMn).
3. Once the desired battery type is selected, wait for 5 seconds without pressing any button. The indicator will stop flashing, and the setting will be saved.

The secondary battery (BATT2) is typically charged as a lead-acid battery and does not require specific type selection.

5.3 LED үзүүлэлтүүд

The front panel features LED indicators to show the operational status:

• PV Status LED: Indicates solar panel input status.
• BATT1 Status LEDs: Show the charging stage and state of charge for the main battery.
• BATT2 Status LED: Indicates charging status for the starter battery.
• Алдааны LED: Illuminates to indicate a fault or warning. Refer to the troubleshooting section.

Figure 6: Installed charge controller showing illuminated LED indicators.

5.4 Цэнэглэх үйл явц

The MPPT Pro Duo uses an adaptive three-level charging algorithm to optimize battery health and lifespan. It prioritizes charging the main battery (BATT1) and then provides a maintenance charge to the starter battery (BATT2).

• Бөөнөөр төлөх төлбөр: Батерейг хурдан цэнэглэхийн тулд хамгийн их гүйдэл өгдөг.
• Шингээх хураамж: Тогтмол эзлэхүүнийг хадгалдагtage to fully charge the battery without overcharging.
• Хөвөгч төлбөр: Эзлэхүүнийг бууруулдагtage to a lower level to maintain the battery at full charge and compensate for self-discharge.

6. Засвар үйлчилгээ

Regular maintenance ensures the longevity and optimal performance of your charge controller:

• Харааны үзлэг: Periodically check for loose connections, damaged wiring, or signs of corrosion.
• Цэвэрлэгээ: Keep the controller clean and free of dust. Use a dry cloth to wipe the exterior. Do not use liquids or solvents.
• Агааржуулалт: Ensure the heatsink fins are not obstructed to allow for proper heat dissipation.
• Холболт шалгах: Verify that all terminal connections are tight and secure.
• Батерейны эрүүл мэнд: Monitor the health of your batteries. A failing battery can affect the performance of the entire system.

7. Алдаа засах

If you encounter issues with your MPPT Pro Duo, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact Offgridtec customer support.

8. Техникийн үзүүлэлтүүд

9. Баталгаат хугацаа ба дэмжлэг

For warranty information, please refer to the terms and conditions provided at the time of purchase or contact Offgridtec GmbH directly. Keep your proof of purchase for any warranty claims.

For technical support, troubleshooting assistance beyond this manual, or inquiries about accessories, please contact Offgridtec customer service. Contact details can typically be found on the manufacturer's official webсайт эсвэл таны худалдан авалтын баримт бичиг.

10. Ердийн програмууд

The Offgridtec MPPT Pro Duo charge controller is suitable for a variety of off-grid and mobile solar power systems, including:

• Амралт зугаалгын тээврийн хэрэгсэл (RV) болон Campэрванчууд
• Marine Systems (Boats & Yachts)
• Remote Telecommunication Stations
• Off-grid Cabins and Small Homes
• Camping and Outdoor Solar Setups

Зураг 7: Жишээ ньamples of typical applications for the MPPT Pro Duo charge controller.