Wavtech link2 2-Channel Line Output Converter User Manual

1. Танилцуулга

This manual provides detailed instructions for the installation, operation, and maintenance of your Wavtech link2 2-Channel Line Output Converter. Please read this manual thoroughly before attempting installation or operation to ensure proper function and to prevent damage to the unit or connected components. The Wavtech link2 is designed to convert high-level speaker signals from a factory or aftermarket head unit into low-level RCA signals, allowing for the addition of aftermarket amplifiers to your audio system.

2. Аюулгүй байдлын мэдээлэл

• Цахилгааны ажил эхлэхийн өмнө тээврийн хэрэгслийн аккумуляторын сөрөг терминалыг үргэлж салгаж байгаарай.
• Богино холболт, эвдрэлээс урьдчилан сэргийлэхийн тулд бүх утсыг зөв тусгаарлаж, найдвартай хамгаална.
• Do not install the unit in locations where it may be exposed to excessive heat, moisture, or direct sunlight.
• Хэрэв та суулгах процессын аль нэг хэсэгт эргэлзэж байвал мэргэжлийн машины аудио суурилуулагчтай зөвлөлдөөрэй.
• Use appropriate fuses for all power connections to protect against electrical surges.

3. Багцын агуулга

Бүх зүйл багцад байгаа эсэхийг шалгана уу:

• Wavtech link2 2-Channel Line Output Converter

4. Бүтээгдэхүүн дууссанview

The Wavtech link2 is a compact and efficient line output converter. Familiarize yourself with its components and connections.

Зураг 4.1: Урд view of the Wavtech link2, showing the Wavtech logo and 'link2' model designation.

Зураг 4.2: Топ view of the Wavtech link2, illustrating the power (PWR), detect (DETECT), power supply (PWR SUPPLY), speaker input (SPK INPUT), clip indicator (CLIP), and gain control (GAIN) sections.

Зураг 4.3: Арын view of the Wavtech link2, displaying the CH1(L) and CH2(R) RCA output connectors.

Зураг 4.4: Топ view of the Wavtech link2, indicating approximate width (2.5 inches) and depth (2.9 inches) dimensions.

Зураг 4.5: Хажуу тал view of the Wavtech link2, showing the approximate height dimension (1.1 inches).

5. Тохиргоо ба суурилуулалт

Тохиромжтой гүйцэтгэлийн хувьд зөв суурилуулалт маш чухал юм. Эдгээр алхмуудыг анхааралтай дагана уу.

5.1 утас холболт

1. Power Supply (PWR SUPPLY):
   • GND: Connect to a clean, solid chassis ground point in the vehicle. Ensure good metal-to-metal contact.
   • + 12V: Connect to a constant +12V power source from the vehicle's battery, fused appropriately (e.g., 1A fuse, not included).
   • ДАХЬ: Connect to the remote turn-on output of your head unit (if available). This will turn the link2 on/off with the head unit.
   • ХЭЛЭХГҮЙ: Provides a remote turn-on signal for your aftermarket ampнастан.
2. Speaker Input (SPK INPUT): Connect the high-level speaker wires from your factory or aftermarket head unit to these terminals. Ensure correct polarity.
   • CH1(L) + / -: Connect to the left channel speaker output wires.
   • CH2(R) + / -: Connect to the right channel speaker output wires.
   • The link2 accepts up to 40V RMS input.
3. Output (OUTPUT): Connect standard RCA cables from the link2's CH1(L) and CH2(R) outputs to the input of your aftermarket ampнастан.

5.2 DETECT Switch

The DETECT switch manages how the link2 turns on and off.

• АСААЛТ: The link2 will turn on when it detects an audio signal on the speaker inputs. This is suitable for most factory systems that do not provide a remote turn-on wire.
• OFF (DC AUD): The link2 will turn on when it detects a DC offset on the speaker inputs. This is common in some factory systems.
• If using the REM IN terminal for turn-on, the DETECT switch setting is less critical, but it is generally recommended to set it to 'OFF' or 'DC AUD' if a dedicated remote wire is used.

5.3 Олз тохируулга

The GAIN knob controls the output level of the link2. Adjust this to match the input sensitivity of your ampнастан.

• Start with the GAIN knob fully counter-clockwise (minimum).
• Play a test tone (e.g., 0dB, 1kHz) at about 75% of your head unit's maximum volume.
• Slowly turn the GAIN knob clockwise until the CLIP indicator light just begins to flicker, then back it off slightly until the light remains off. This ensures a clean, unclipped signal to your ampнастан.

5.4 Load Sense

The link2 features load detect functionality for factory systems that require resistance on the speaker outputs to remain active. This ensures the factory head unit does not shut down or reduce output when connected to the link2.

6. Ашиглалтын заавар

Once installed and configured, the Wavtech link2 operates automatically. It will turn on and off with your head unit based on the DETECT switch setting or the remote input. The primary operational aspect is ensuring the gain is set correctly to provide a clean signal to your amplifier without clipping.

7. Засвар үйлчилгээ

The Wavtech link2 requires minimal maintenance.

• Төхөөрөмжийг тоос шороо, хог хаягдлаас хол байлга. Цэвэрлэхэд зөөлөн, хуурай даавуу ашиглаарай.
• Бүх холболтууд найдвартай байгаа эсэхийг шалгаарай. Утаснууд элэгдэл, зэврэлтийн шинж тэмдэг байгаа эсэхийг үе үе шалгаж байгаарай.
• Төхөөрөмжийг хэт өндөр температур эсвэл чийгэнд оруулахаас зайлсхий.

8. Алдаа засах

If you encounter issues with your Wavtech link2, refer to the following common problems and solutions:

9. Техникийн үзүүлэлтүүд

• Барааны жин: 8 унц
• Бүтээгдэхүүний хэмжээ: 78.74 x 78.74 x 23.62 inches (Note: These dimensions appear to be incorrect based on product images showing 2.5" x 2.9" x 1.1". Please refer to physical product for accurate measurements.)
• Загварын дугаар: link2
• ASIN: B09BB4SRTY
• Үйлдвэрлэгч: Wavtech
• Оролтын хэмжээtage: Up to 40V RMS (Speaker Level)
• Сувгууд: 2 суваг
• Онцлогууд: Load Detect, Remote Turn-On Output

10. Баталгаат хугацаа ба дэмжлэг

The Wavtech link2 comes with a 1 жилийн үйлдвэрлэгчийн баталгаа. For warranty claims or technical support, please contact Wavtech customer service or the authorized dealer from whom you purchased the product. Keep your proof of purchase for warranty validation.

For further assistance, visit the Wavtech website or consult your local authorized dealer.