Гарын авлага+

KICKER 48TRTP122+CANDY-X1B+AMPKIT4

KICKER 48TRTP122 Subwoofer and DS18 CANDY-X1B Amplifier системийн хэрэглэгчийн гарын авлага

Model: 48TRTP122+CANDY-X1B+AMPKIT4

1. Бүтээгдэхүүн дууссанview

This manual provides instructions for the KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, the DS18 CANDY-X1B Mono Class D Amplifier, and the accompanying DS18 AMPKIT4 4AWG Complete Amplifier Wiring Kit. This system is designed to enhance your vehicle's audio experience with powerful bass output.

2. Хайрцагт юу байна

Contents of the DS18 AMPKIT4 4AWG Complete Amplifier Kit, showing various wires, fuse holder, terminals, and cable ties.

Figure 2.1: Components of the DS18 AMPKIT4 4AWG Complete Ampөргөгч иж бүрдэл.

3. Тохиргоо ба суурилуулалт

Тохиромжтой гүйцэтгэл, аюулгүй байдлыг хангахын тулд зөв суурилуулах нь чухал юм. Хэрэв та ямар нэгэн алхам хийх талаар эргэлзэж байвал мэргэжлийн машины аудио суулгагчтай зөвлөлд.

3.1 Аюулгүй байдлын урьдчилан сэргийлэх арга хэмжээ

3.2 Subwoofer Enclosure Placement

The KICKER 48TRTP122 is a down-firing enclosure, designed to be placed in the trunk or cargo area of your vehicle. Ensure it is securely fastened to prevent movement during driving.

KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, black carpeted finish.

Figure 3.1: KICKER 48TRTP122 Down-Firing Subwoofer Enclosure.

3.3 Ampилүү урт холбох

Mount the DS18 CANDY-X1B amplifier in a location that allows for adequate ventilation and protection from moisture. Common locations include under a seat, in the trunk, or on the back of a rear seat. Ensure it is securely mounted to prevent vibration damage.

DS18 CANDY-X1B Mono Class D Amplifier, black with red accents.

Figure 3.2: DS18 CANDY-X1B Mono Class D Ampнастан.

3.4 Утас тавих заавар

Follow these steps carefully for wiring the system. Refer to the wiring diagram below for visual guidance.

  1. Power Wire (Red 4 AWG): Run the 17 ft red power wire from the vehicle's positive battery terminal to the fuse holder, then from the fuse holder to the +12V terminal on the DS18 amplifier. Ensure the fuse holder is installed close to the battery (within 18 inches).
  2. Ground Wire (Black 4 AWG): Connect the 3 ft black ground wire from the GND terminal on the ampөргөгчийг тээврийн хэрэгслийн явах эд анги дээрх цэвэрхэн, будаггүй металл гадаргуу дээр байрлуулна. Цахилгааны холболт сайн байгаа эсэхийг шалгаарай.
  3. Алсын зайнаас асаах утас: Connect the remote wire from your head unit's remote output to the REM terminal on the ampөргөгч. Энэ утас эргүүлдэг ampөргөгчийг толгойн нэгжээрээ асааж унтраа.
  4. RCA кабель: Connect the RCA cables from your head unit's subwoofer output (or full-range output if no dedicated sub output) to the RCA input jacks on the DS18 ampнастан.
  5. Чанга яригч утас: Чанга яригчийг утаснаас холбоно уу amplifier's speaker output terminals to the KICKER subwoofer enclosure's input terminals. Ensure correct polarity (+ to + and - to -). The KICKER 48TRTP122 enclosure has a 2-ohm impedance.
  6. Басс удирдлага: Connect the included bass remote to the dedicated remote port on the DS18 amplifier. Mount the remote in an accessible location for easy adjustment.
Wiring diagram showing a 2-ohm subwoofer connected to a 2-ohm amplifier output, with positive and negative terminals clearly marked.

Figure 3.3: Subwoofer to Amplifier Wiring Diagram (2-ohm connection).

DS18 Bass Remote control unit with a rotary knob and connected cable.

Figure 3.4: DS18 Bass Remote Control.

4. Ашиглалтын заавар

Once the system is installed, follow these steps to configure and operate your subwoofer and ampнастан.

4.1 Initial Power-Up and Gain Setting

  1. Тээврийн хэрэгслийн сөрөг зайны терминалыг дахин холбоно уу.
  2. Толгой төхөөрөмжөө асаана уу. amplifier should power on (indicated by a blue LED on the ampилүү амьд).
  3. -г тохируулах amplifier's GAIN control to its minimum (fully counter-clockwise) position.
  4. Play a music track with strong bass at a moderate volume level on your head unit (around 75% of maximum volume).
  5. GAIN хяналтыг аажмаар нэмэгдүүлнэ үү amplifier until you hear distortion, then back it off slightly until the sound is clear. This sets the maximum clean output level.

4.2 Amplifier Controls (DS18 CANDY-X1B)

The DS18 CANDY-X1B amplifier features several controls for fine-tuning your bass output:

Close-up of the DS18 CANDY-X1B amplifier's control panel, showing gain, bass boost, LPF, subsonic filter, and phase controls.

Figure 4.1: DS18 CANDY-X1B Amplifier Controls.

5. Засвар үйлчилгээ

Regular maintenance ensures the longevity and optimal performance of your audio system.

6. Алдаа засах

Нийтлэг асуудлууд болон тэдгээрийн шийдлүүдийг энэ хэсгээс харна уу.

АсуудалБоломжит шалтгаанШийдэл
Сабвуферээс дуу гарахгүй байна
  • Хүч чадалгүй ampнастан
  • Сул RCA эсвэл чанга яригчийн холболтууд
  • Толгой хэсгийн тохиргоо
  • Ampхамгаалах горимд өргөгч
  • Check power, ground, and remote wires. Verify fuse.
  • Ensure all RCA and speaker wires are securely connected.
  • Check head unit's subwoofer output settings and volume.
  • Унтраад дахин эхлүүлнэ үү amplifier. Check for shorts in speaker wiring.
Гажуудсан дуу чимээ
  • Олзыг хэт өндөр тохируулсан
  • Bass boost too high
  • Clipping from head unit
  • Гэмтсэн чанга яригч утас
  • Бууруулах ampөсгөгч олз.
  • Lower bass boost setting.
  • Reduce head unit volume.
  • Чанга яригчийн утсыг гэмтсэн эсвэл богино холболттой эсэхийг шалгана уу.
Ampөргөгч хэт халсан
  • Агааржуулалт хангалтгүй
  • Буруу импеданс ачаалал
  • Олзыг хэт өндөр тохируулсан
  • Баталгаажуулах amplifier has clear airflow.
  • Сабвуферийн импедансын тохирлыг шалгах amplifier's stable load (2 ohms for this system).
  • Бууруулах ampөсгөгч олз.
Bass remote not working
  • Сул холболт
  • Гэмтсэн кабель
  • Check the connection of the remote cable to the ampнастан.
  • Кабелийг харагдахуйц гэмтэл байгаа эсэхийг шалгана уу.

7. Техникийн үзүүлэлтүүд

Detailed specifications for the components in this bundle.

7.1 KICKER 48TRTP122 12" CompRT Subwoofer Enclosure

7.2 DS18 CANDY-X1B Mono Class D Ampнастан

7.3 DS18 AMPKIT4 4AWG Complete Ampөргөгч иж бүрдэл

8. Баталгаат хугацааны мэдээлэл

This product bundle typically comes with a manufacturer's warranty. The KICKER 48TRTP122 subwoofer enclosure and DS18 CANDY-X1B amplifier are covered by a full warranty from their respective manufacturers. Specific warranty terms, duration, and coverage details may vary. Please retain your proof of purchase for warranty claims.

For detailed warranty information, refer to the documentation included with each individual component or visit the respective manufacturer's official webсайт.

9. Дэмжлэг

If you encounter issues not covered in this manual or require further assistance, please contact the manufacturer's customer support:

When contacting support, please have your product model numbers (48TRTP122, CANDY-X1B, AMPKIT4) and proof of purchase readily available.