1. Танилцуулга
This manual provides essential information for the safe and effective operation of your FLIPSKY 75100 Pro V2.0 Speed Controller. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of the device.
The FLIPSKY 75100 Pro V2.0 is an advanced Electronic Speed Controller (ESC) designed for electric skateboards, scooters, and e-bikes. It features an aluminum PCB for enhanced heat dissipation and supports various control modes and sensor types.
2. Аюулгүй байдлын мэдээлэл
- Always disconnect power before performing any installation, maintenance, or wiring changes.
- Ensure all connections are secure and correctly polarized to prevent damage to the ESC or other components.
- ESC-г заасан хэмжээнд нь ажиллуулна ууtage and current limits to avoid overheating and component failure.
- ESC-г ус, чийг болон хэт өндөр температураас хол байлга.
- Installation should be performed by individuals with adequate knowledge of electronics and electrical systems.
- Regularly inspect wiring and connections for signs of wear or damage.
3. Бүтээгдэхүүний онцлог
The FLIPSKY 75100 Pro V2.0 ESC incorporates several key features for robust and flexible performance:
- Firmware: 6.02 (firmware update supported)
- Adjustable protection against: low voltage, өндөр ботьtage, over current, temperature abnormal, MOSFETs/motor over temperature.
- Support for BLDC square wave mode control and FOC sine wave mode.
- Aluminum PCB for enhanced heat dissipation and extended lifespan.
- Programmable functionality.
- Regenerative braking capacity.
- Integrated power switch button (Red).
Figure 1: FLIPSKY 75100 Pro V2.0 Speed Controller with various connection wires and power button.
4. Тохиргоо ба холболтууд
Proper connection of the ESC is critical for its functionality and safety. Refer to the connection diagram below for guidance.
Figure 2: Connection diagram illustrating battery, motor, and control signal ports.
4.1. Эрчим хүчний холболт
- Зай: Connect your battery pack to the main power input wires (red for positive, black for negative). Ensure correct polarity. The ESC supports 14-84V (4-20S) input.
- Мотор: Connect the three motor phase wires to the corresponding output wires from the ESC. The wires are typically black and do not require specific phase matching; the ESC will handle it.
- Эрчим хүч солих: Connect the red power switch button to its designated port.
4.2. Control and Sensor Connections
- HALL Sensors: Connect the motor's HALL sensor wires to the HALL port on the ESC. Supported sensors include ABI, HALL, AS5047, AS5048A.
- PPM/PWM: For throttle input, connect your receiver's PPM/PWM signal to the PPM port.
- CAN автобус: Use the CAN port for communication between multiple ESCs (master/slave configuration) or other CAN-enabled devices.
- UART: The UART port allows for communication with external modules like Bluetooth modules or other microcontrollers.
- USB: Connect the ESC to a computer via the USB port for configuration and firmware updates using VESC Tool software.
- ADC: Analog-to-Digital Converter ports are available for various analog inputs.
Чухал: When unplugging connectors, press the release tab to avoid damaging wires or the connector itself.
5. Ашиглалтын заавар
After successful installation and configuration using the VESC Tool, the ESC is ready for operation.
- Асаах: Press the red power switch button to turn on the ESC. The LED indicator will illuminate.
- Тохируулагчийн удирдлага: Apply throttle input via your connected PPM/PWM device. The ESC will control the motor speed and direction based on your input and configured settings.
- Тоормослох: The ESC supports regenerative braking. Applying reverse throttle will engage braking, which also recharges the battery to some extent.
- Хяналт: Use the VESC Tool connected via USB or UART (e.g., Bluetooth module) to monitor real-time parameters such as motor RPM, current, voltage, ба температур.
- Унтраах: Press and hold the red power switch button to turn off the ESC.
6. Засвар үйлчилгээ
- Тогтмол үзлэг: Бүх утас болон холбогчийг элэгдэл, зэврэлт эсвэл сул холболтын шинж тэмдэг байгаа эсэхийг үе үе шалгаж байгаарай.
- Цэвэрлэгээ: Keep the ESC clean and free from dust, dirt, and debris. Use a soft, dry brush or compressed air. Avoid using liquids.
- Дулааны менежмент: Ensure adequate airflow around the ESC, especially during high-power operation, to utilize its aluminum PCB's heat dissipation capabilities effectively.
- Програм хангамжийн шинэчлэлтүүд: Check for and apply firmware updates periodically using the VESC Tool to benefit from performance improvements and bug fixes.
7. Алдаа засах
| Асуудал | Боломжит шалтгаан | Шийдэл |
|---|---|---|
| ESC асаалттай биш байна. | No power from battery, faulty power switch, incorrect wiring. | Зайны хэмжээг шалгана ууtage, inspect power switch connection, verify main power wiring. |
| Motor not spinning or erratic behavior. | Incorrect motor detection, loose motor phase wires, sensor issues, incorrect VESC Tool configuration. | Perform motor detection in VESC Tool, check motor wire connections, inspect sensor wiring, review VESC Tool settings. |
| ESC overheating. | Excessive load, insufficient cooling, short circuit, incorrect current limits. | Reduce load, ensure adequate airflow, check for shorts, adjust current limits in VESC Tool. |
| Хийн тохируулгын хариу үйлдэл байхгүй. | PPM/PWM signal not connected, incorrect receiver settings, VESC Tool input configuration error. | Verify PPM/PWM connection, check receiver output, configure input in VESC Tool. |
8. Техникийн үзүүлэлтүүд
| Онцлог | Дэлгэрэнгүй |
|---|---|
| Програм хангамж | 6.02 (firmware update supported) |
| Хэмжээ (L*W*H) | 103мм * 58мм * 27.7мм |
| Ботьtage Хамрах хүрээ | 14-84V (4-20S) |
| Тасралтгүй гүйдэл | 100 А |
| BEC гаралт | 5V@1.5A |
| Хяналтын горимууд | BLDC square wave, FOC sine wave |
| Max ERPM | 150000 |
| Control Interface Ports | USB, CAN, UART |
| Дэмжигдсэн мэдрэгч | ABI, HALL, AS5047, AS5048A |
| Input Set Support | PPM, ADC, NRF, UART |
| Утасны хэмжээ | 10AWG (75100 Pro) |
| Програмчлагдах боломжтой | Тиймээ |
| Regenerative Capacity | Тиймээ |
| Фазын шүүлтүүр | Тиймээ |
| Цахилгаан унтраах товчлуур | Улаан |
| Материал | Хөнгөн цагаан |
| Зүйлийн жин | 0.3 кг |
Figure 3: Dimensions of the FLIPSKY 75100 Pro V2.0 Speed Controller.
9. Баталгаат хугацаа ба дэмжлэг
9.1. Баталгаат хугацааны мэдээлэл
The FLIPSKY 75100 Pro V2.0 Speed Controller comes with a warranty of 2 months or more, as specified by the manufacturer. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects under normal use conditions. Damage resulting from improper installation, misuse, modification, or exceeding specified limits may void the warranty.
9.2. Техникийн дэмжлэг
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact FLIPSKY customer support through their official website or the retailer from whom the product was purchased. Ensure you have your product model number and purchase details ready.
10. Нэмэлт бүтээгдэхүүн Views
Зураг 4: Өөр view of the FLIPSKY 75100 Pro V2.0 with connected wires.
Зураг 5: Дээд тал view of the FLIPSKY 75100 Pro V2.0, highlighting the ports and branding.
Зураг 6: Хажуу тал view of the FLIPSKY 75100 Pro V2.0, showcasing the ribbed aluminum casing нь дулаан ялгаруулалтын хувьд.
Зураг 7: Өнцөг view of the FLIPSKY 75100 Pro V2.0.
Зураг 8: Урд view of the FLIPSKY 75100 Pro V2.0.
Зураг 9: Дотоод view of the FLIPSKY 75100 Pro V2.0 circuit board, showing components and capacitors.
Энэ гарын авлагад оруулахад хамааралтай худалдагчийн албан ёсны бүтээгдэхүүний видео бичлэг олдсонгүй.
