Мөрдөх боломжтой 5002CC Лабораторийн таймер

Сэрүүлэг
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

Дэлгэцийг тэг болгох

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

ЦАГИЙН АЖИЛЛАГАА

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

БУЦАХ ХУГАЦАА ТОХИРУУЛЖ БАЙНА

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

ЖИЧ: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two examples өгсөн байна.

Example 1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. 2 товчийг дарна уу.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Example 2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. 3 товчийг дарна уу.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

Үзүүлэлтүүд

• Дэлгэц: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• Шийдвэр: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

ШУУРХАЙ ЛАВЛАГАА

• A- Суваг харагдана
• B- Нэгдүгээр суваг (1) товчлуур
• C- Хоёрдугаар суваг (2) товчлуур
• D- Гуравдугаар суваг (3) товчлуур
• Цахим суваг нь цагийг заагаагүй эсвэл харагдахгүй байна
• F-Суваг цаг тохируулж байгаа боловч харагдахгүй байна
• G- Цаг (H) товчлуур
• H- Minutes (M) button
• I – Seconds (S) button

Сувгийн үзүүлэлтүүд
LCD indicators report the status of each channel.

БАТАРЕЙ СОЛИХ

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

Зайгаа оруулсны дараа таймер дэлгэц хэвийн ажиллаж байгаа эсэхийг шалгаарай. Хугацаатай ажиллах явцад дэлгэц дээр анивчсан сегментүүд гарч ирж болно. Хэрэв ийм зүйл тохиолдвол батерейг салгаж, дахин оруулах замаар дахин тохируулаарай. Батерейны багц бүр хэвийн нөхцөлд 1-2 жил ажиллах ёстой. Батерейг солих шаардлагатай үед LCD дэлгэц хоосон хэвээр байх болно.

БАТАЛГАА

БАТАЛГААТ, ҮЙЛЧИЛГЭЭ ЭСВЭЛ ДАХИН ШАЛГАРУУЛГА
Баталгаат, үйлчилгээ эсвэл дахин тохируулгын талаар дараахтай холбогдоно уу:

МӨРДӨХ БҮТЭЭГДЭХҮҮН 12554 Old Galveston Rd. Suite B230 Webстер, Техас 77598 АНУ

• Ph. 281 482-1714
• Факс 281 482-9448
• И-мэйл support@traceable.com
• www.traceable.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

Муур. 5002 дугаар
Traceable® нь Cole-Parmer-ийн бүртгэлтэй худалдааны тэмдэг юм.

©2020 Traceable® бүтээгдэхүүн. 92-5002-00 Илч 6 070825

Түгээмэл асуултууд

Баримт бичиг / нөөц

Мөрдөх боломжтой 5002CC Лабораторийн таймер [pdf] Хэрэглэгчийн гарын авлага 5002CC Lab Timer, 5002CC, Lab Timer, Timer

Лавлагаа

• Хэрэглэгчийн гарын авлага